PRODIM ORCABOT XXL PRO2 Manual Download Page 26 | Manualshive

Page: 26 / 41

background image

Manual: Orcabot XXL

Pro 2

version 1.0.1 Mar 2017

26

www.prodim-systems.com

-

□ Select extr. 1
Selection of extruder 1.

-

□ Select extr. 2
Selection of extruder 2.

-

Move extruder
Move extruder to extrude filament.

-

□ No Copies
Turn printer OFF “copy” mode.

-

□ 1 Copy
Turn printer ON “copy”mode.

SD card (only visible with SD card present)

-

Print file
Direct selection of file on a SD-card.

-

Delete file
Delete a file from the SD-kaart.

Setup

-

Preheat Temperatures
Preheat temperature value extruder 1, extruder 2 and bed.

-

Ignore M106 cmd □

Ignore the M106 code. (M106 code is present when autocooling is on.

Settings

-

Language
Selection of the userinterface language

-

Extruder

o

□ Select extr. 1
Selection of extruder 1.

o

□ Select extr. 2
Selection of extruder 2.

o

X-Offset
Adjustment of X-offset of selected extruder.

o

Y-Offset
adjustment of Y-offset of selected extruder.

o

Z-Offset
Adjustment of Z-offset of selected extruder.

«
...
24
25
26
27
28
...
»

Summary of Contents for ORCABOT XXL PRO2










































Reviews:

No comments

Related manuals for ORCABOT XXL PRO2

Brand: Xerox Pages: 68

Brand: ABLE Pages: 26

Brand: F+D Feinwerk- und Drucktechnik Pages: 41

Brand: Oki Pages: 6

Brand: Oki Pages: 32

Brand: Oki Pages: 52

Brand: Oki Pages: 64

Brand: Oki Pages: 269

Brand: Oki Pages: 2

Brand: Oki Pages: 32

Brand: Oki Pages: 33

Brand: Oki Pages: 8

Brand: Oki Pages: 101

Brand: Oki Pages: 104

Brand: Oki Pages: 99

Brand: Oki Pages: 112

Brand: Oki Pages: 100

Brand: Oki Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands