background image

 

PRODUCT FEATURES  

 

SAFETY PILOT 

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. ODS/pilot shuts off the heater 
if there is not enough fresh air. 

 

PIEZO IGNITION SYSTEM  

This heater is equipped with an electronic piezo control system. This system requires AAA batteries (provided). 

 
THERMOSTAT HEAT CONTROL AND REMOTE CONTROL  

The control automatically cycles the burner on and off to maintain a desired room temperature. See page 17. 

 
DUAL FUEL CAPABLE

 

Your heater is equipped to operate on either Propane or Natural gas. The heater is shipped from the factory ready for 
connecting to Propane. The heater can easily be changed to Natural gas by having your qualified installer follow the 
instructions on page 12~13 and the markings on the heater. 

 

State of Massachusetts: 

The installation must be made by a licensed plumber or gas fitter in the 

Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired supplemental room 
heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.  
 
In the State of Massachusetts, unvented propane or natural gas-fired space heaters shall be prohibited in 
bedrooms and bathrooms.  

 

In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts 
requires that a flexible appliance connector cannot exceed three feet in length. 

 
LOCAL CODES 

 

Install and use heater with care. Follow all codes. In the absence of local codes, use the latest edition of 

The National 

Fuel Gas Code

,  ANSI Z223.1, also known as NFPA 54*.  

 
*Available from:  
 
 
 
 
 
This heater is designed for vent-free operation. State and local codes in some areas prohibit the use of vent-free heaters.  

 
 

 
 
 
 
 
 
 
 
 
 
 

  American National Standards Institute, lnc.         National Fire Protection Association, lnc. 
1430 Broadway                                                      1 Batterymarch Park 

New York, NY 10018                                            Quincy, MA  02269-9101 

Summary of Contents for BD23TCC-2-LO




























Reviews: