Pro Spot Hybrid Spot Instruction Manual Download

Page: 8 / 36

2 Safety

Page 7

When the Spot Gun is used continuously, the welding cables get hot.

To prevent the welder from malfunctioning due to overheating, it is

cooled using the built-in air cooling system. The air cooling system

cools the welding cables, cable ends and the spot gun.

2.3.1 Cooling

2.3 Safety devices

To activate the cooling system, turn the air cooling ON. Compressed air

will flow through the weld cables. It is not necessary to leave on at all

times, but should be used when the weld cables are hot to the touch.

For best results, let the welder rest when cables are too hot. Cooler weld

cables result in better weld performance.

2.2 Warnings and important notices (cont’d.)

SHIELD EYES EXPLOSIVE GASES

Can cause blindness or injury.

NO SPARKS, FLAMES OR SMOKING

SULFURIC ACID

Can cause blindness or severe burns.

FLUSH EYES IMMEDIATELY

With water. Get medical help fast.

IF SWALLOWED

Drink as much water or milk as possible. Get medical help fast.

IF SPILLED

Spread baking SODA over spill, then dilute with large amounts of water.

KEEP OUT OF REACH OF CHILDREN

Do Not Tip, Keep Vent Caps Tight And Level

PROPOSITION 65 WARNING

Battery posts, terminals and related accessories contain lead and lead

compounds, chemicals known to the State of California to cause cancer and

reproductive harm. Batteries also contain other chemicals known to the State

of California to cause cancer. Wash hands after handling.

KEEP OUT OF REACH OF CHILDREN

DANGER/POISON

SPARKS

FLAMES

SMOKING

FLUSH EYES

IMMEDIATELY

WITH WATER.

SULFURIC

ACID

CAN

CAUSE

BLINDNESS OR

SEVERE BURNS.

GET

MEDICAL

HELP FAST.

SHIELD

EYES.

EXPLOSIVE

GASES CAN

CAUSE BLINDNESS

OR INJURY.

OPEN CIRCUIT VOLTAGE AS IT RELATES TO STATE OF CHARGE

Open Circuit Voltage*

State of Charge

12.80 or greater.............................100%

12.60..................................75%

12.30..................................50%

12.00..................................25%

12.00....................................0

* The actual stabilized OCV can only be determined after the

battery has been disconnected from the charger for 24 hours.

Battery Warnings

Hybrid Spot

Summary of Contents for Hybrid Spot





































Search results

Summary of Contents for Hybrid Spot

Reviews:

Related manuals for Hybrid Spot

Brands by name

Popular brands

Pro Spot Hybrid Spot, Instruction Manual

Search results

Summary of Contents for Hybrid Spot

Reviews:

Related manuals for Hybrid Spot

Brands by name

Popular brands