background image

22

MAINTENANCE

Regular maintenance is important for optimal 

performance and to reduce wear. Inspect and properly 

tighten all parts each time the exercise bike is used. 

Replace any worn parts immediately.

To clean the exercise bike, use a damp cloth and a 

small amount of mild soap. IMPORTANT: To avoid 

damage to the console, keep liquids away from 

the console and keep the console out of direct 

sunlight.

CONSOLE TROUBLESHOOTING

The console requires activation. If you have not 

activated the console, see assembly step 14 on 

page 13.

If the console does not turn on, make sure that the 

power adapter is fully plugged in.

If a replacement power adapter is needed, call the 

telephone number on the cover of this manual. 

IMPORTANT: To avoid damaging the console, use 

only a manufacturer-supplied regulated power 

adapter.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the 

reed switch should be adjusted. 

To adjust the reed switch, first unplug the power 

adapter. Then, you must remove the rear and front 

upright covers as described below.

See assembly step 5 on page 9. Using a standard 

screwdriver, release the tabs along the bottom edges 

of the Rear and Front Upright Covers (19, 20), remove 

the two M4 x 12mm Screws (57), and then remove the 

Rear and Front Upright Covers.

Locate the Reed Switch (35). Turn the Crank (40) 

until a Magnet (39) is aligned with the Reed Switch. 

Next, loosen, but do not remove, the two indicated 

M4 x 12mm Flange Screws (36). Slide the Reed 

Switch slightly closer to or away from the Magnet, and 

then retighten the Flange Screws. 

Plug in the power adapter and turn the Crank (40) so 

that the Magnet (39) passes the Reed Switch (35) 

repeatedly. Repeat these actions until the console 

displays correct feedback. 

When the reed switch is correctly adjusted, reattach 

the rear and front upright covers.

36

35

39

40

MAINTENANCE AND TROUBLESHOOTING

Summary of Contents for 235 CSX





























Reviews: