43
5.
STOVE OPERATION
5.1.
Preparation for initial ignition
Open the side panels and visually inspect
for any defects. Look around and find the
command control unit, which represents a
black plastic box and remove the battery
protective strip by pulling it out.
Install the control panel
–
display, at the
top end on the back of the stove, as shown in
the right diagram and connect it to the main
circuit board, using the enclosed cable with
cable couplers. After the final completion of all
installation works, make sure that you
have read
and are familiar with all instructions.
WHS must be filled and bled.
Room temperature sensor must be outside
the appliance body to provide correct
measurement.
Use the power supply cable from the
complete set of the stove to connect it to the
Schuco type wall socket
.
Verify all available settings at the panel
-
display and perform any adjustments, if
necessary.
Verify the indication of the clock and the calendar.
Carefully fill the hopper observing for any objects or materials, which are not pellets.
Before switching on the heating appliance for the first time or when the fuel has ran out,
the delivery auger is empty. To fill it up, please use the menu and go to „Settings“, „Manual
feeding“ and hold down the „Dose“ button. This action will be on for 30 sec. If this was not
enough, please repeat the procedure.
CAUTION!
Verify whether the firepot has been correctly installed.
5.2.
Ignition, fire
-
up and shutting down the stove
The process of ignition consists in several stages. Upon the "Start” command the stove
begins with a cycle of intense air purging of the firebox, in order to guarantee the
cleanliness of the firepot. Ignition is done with the help of a 250W electrical heater and a
forced supply of air, which flows around it being thus heated to a temperature, which is
sufficient to kindle the initial dose of pellets fed into the firepot. This process continues
Summary of Contents for KPW 24
