Primedic DefiMonitor XD Operating Instructions Manual Download Page 80 | Manualshive

Page: 80 / 116

Primedic DefiMonitor XD Operating Instructions Manual Download Page 80

Cleaning, maintenance and dispatch

80 / 116

DefiMonitor XD 21324 / GB / K05

METRAX GmbH

When doing so, pay attention to the following:

DANGER

•

If parts of the housing or insulation are damaged, they must be
repaired or exchanged immediately.

•

If parts of the housing or insulation are damaged, do not use the
device or switch it off immediately.

•

Have the device repaired as soon as possible by the
manufacturer.

Note

For more detailed information on the regular safety and metrological checks in
accordance with the Ordinance on the Operation and Use of Medical Devices
(MPBetreibV), refer to Chapter 24

13.3

Dispatching the PRIMEDIC™ DefiMonitor XD

Note

If the equipment is to be sent out for upgrading or servicing, in that case the power
module must always be removed from the device and must be sent in with the
device, but packaged separately.

Where possible, use the original box.

«
...
78
79
80
81
82
...
»

Summary of Contents for DefiMonitor XD





















































































































Reviews:

No comments