manualshive.com logo in svg

Primedic DefiMonitor XD, Operating Instructions Manual, Page: 41 / 116

Share
Download
Primedic DefiMonitor XD Operating Instructions Manual Download Page 41

 

Preparatory measures before (initial) start-up 

 

METRAX GmbH 

DefiMonitor XD 21324 / GB / K05 

41 / 116 

 

5.3.1

 

Inserting PRIMEDIC™ AkuPak 

 

 

Fig. 21

: PRIMEDIC™ DefiMonitor XD

 

–

 

Inserting PRIMEDIC™ A

kuPak 

 

Procedure: 

  Lay the device on its back.  

  Push the (new) power module into the device in the direction shown by the arrow (1) 

until it rests against the left-hand stop. 

  Press the front of the power module into the slot in the direction shown by the arrow (2) 

until you hear a "click" as the unlocking device engages securely with the tongue on 
the power module. 

The power module should now be in fully inserted position, flush with the front housing of the 
device. It should not fall out when the device is moved. If it does, it is not securely engaged.  

Note 

The device switches on automatically when the PRIMEDIC™ AkuPaks battery is 

inserted and performs an automatic self-test.  

Monitor the Status Display. If the display is showing "OK", the device is ready to 
use.  

Switch it off (if required) by pressing the On / Off button.  

 

 

CAUTION 

If the display does not read "OK" or if a fault message appears on 
the monitor, remedy the cause or contact your nearest service 
station. The device will switch itself off. 

 

Summary of Contents for DefiMonitor XD





















































































































Reviews:

No comments