Primedic DefiMonitor XD Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 116

Primedic DefiMonitor XD Operating Instructions Manual Download Page 33

Description of device

METRAX GmbH

DefiMonitor XD 21324 / GB / K05

33 / 116

4.3

Capacity display

The charging status of the PRIMEDIC™ DefiMonitor XD is shown

on the display. The different

possible images displayed have the following meaning:

The charging status of PRIMEDIC™ AkuPak battery is monitored electronically to ensure

optimum display of the capacity.

In addition to this display, the PRIMEDIC™ DefiMonitor XD issues a warni

ng when the battery

charge is running very low.

If the
PRIMEDI

C™

AkuPak
battery is damaged (e.g. as a result of the memory effect), this is shown in the screened area
on the left side of the capacity display.

If the device is being used, the corresponding audible warning will be repeated once a minute
in the selected language.

Note

In order to ensure that the device is always ready for immediate operation,
we recommend that you have a charged replacement battery with you at all
times. Depending on the situation in which this voice message is issued,
you should consider replacing the battery.

Image on display

Meaning

100 % charged

50 % discharged

partly discharged or with reduced capacity

0 % (device runs on until charge is exhausted)

PRIMEDIC

™ AkuPak communication interrupted or operating

life reached.

Voice message

Display on monitor

PRIMEDIC™

AkuPak

< Charging status battery
low, please recharge >

Charging status battery low,
please recharge

«
...
31
32
33
34
35
...
»

Summary of Contents for DefiMonitor XD





















































































































Reviews:

No comments