background image

 

10

 

SPECIFICATIONS

 

 

Power 

 
Type:   

 

 

 

DC 

V+ Connection: 

 

 

12 mm Connector, Pin 1 

Common 

 

 

 

12 mm Connector, Pin 3 

Voltage: 

   10 

to 

24 

volts 

DS71 Max Current:   

 

40 mil output loads 

DS72 Max Current:   

 

40 milliamps 

Protection: 

   Reverse 

polarity 

protected. 

     Transient 

Voltage 

Suppress 

30 

Volts 

 
Logic Output Electrical Specifications

 

 
DS71 Sourcing Outputs 
 
Connection:   

 

 

12 mm Connector, Pin 4 

Max. source current: 

 

50mA, fuse limited 

Output Voltage High: 

 

Supply Voltage less 1 volt 

Over-current protection: 

 

Self-resetting thermal fuse 

ESD 

protection: 

  Transient 

Voltage Suppressor @ 30 Volts  

 
DS72 Sinking Outputs 
 
Open Drain 
Connection:   

 

 

12 mm Connector, Pin 2 

Max. applied voltage: 

 

30 Volts, TVS limited 

Max. current, momentary:   

40 Amps 

Max. current, sustained: 

 

50mA, fuse limited 

Max. off state leakage @ 30 V: 

25uA 

Over-current protection: 

 

Self-resetting thermal fuse. 

ESD 

protection: 

  Transient Voltage Suppressor @ 30 Volts 

 
 
 

Summary of Contents for FLUXIMITY DS71













Reviews: