Price FFU-HE Series Manual Download Page 29

Page: 29 / 64

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Filter/Motor Indicator LED (FL/ML) – BTR

Sample line string below:

FFU-HE/24/48/

BTR

/BC/ECM/115/10//CT//HEPA//ECMDX//WK/DSW/PC/TMB///

/WPF/PL-AL///PL-MILL//

LED Operation

Option

Code

LED

Color

Action

Notes

Filter LED

Green

None

Indicates normal operation until filter pressure drop exceeds calibrat-

ed pressure drop (factory set at 1.5x clean filter pressure).

Yellow

Change Filter

Indicates filter pressure drop has exceeded calbirated setting (factory
set at 1.5x clean filter pressure.

Motor

LED

Green

None

Indicates normal motor operation when the static pressure is above
0.2" w.g.

Red

Troubleshoot Motor

Indicates motor is not in operation, and that unit static pressure is

below 0.2" w.g.

Installation

STEP 1:

Remove BTR filter from box by following the instructions found on page 23 of this installation manual.

STEP 2:

Take LED cable assembly out of FFU-HE Plenum

Cable Assembly

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

Summary of Contents for FFU-HE Series
































































Search results

Summary of Contents for FFU-HE Series

Reviews:

Related manuals for FFU-HE Series

Brands by name

Popular brands

Price FFU-HE Series, Manual

Search results

Summary of Contents for FFU-HE Series

Reviews:

Related manuals for FFU-HE Series

Brands by name

Popular brands