Price FFU-HE Series Manual Download Page 38 | Manualshive

Page: 38 / 64

background image

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Remove Diffuser Face with Quarter Turn Fasteners

STEP 3:

Make note of all wire locations for re-installation later. It is recommended to take a picture of all applicable wires.

STEP 4:

Open control box and disconnect wires at the terminal block, referencing applicable wiring diagram.

STEP 5:

Remove the 6 bolts to free the motor/blower assembly, using a 7/16” socket wrench (or equivalent).

STEP 6:

Remove motor/blower assembly.

STEP 7:

Inspect and/or replace parts.

STEP 8:

Replace with the new motor/blower assembly and reassemble by reversing the above steps.

NOTE:

For information on how to order replacement motor/blowers, contact your local Price Sales Representative. Visit Price’s

website (http://www.priceindustries.com/contact/reps-dealers) to locate your local Representative.

STEP 9:

Double check airflow to ensure that set point hasn’t changed. applicable speed controller found on pages X-X

36

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

FAN FILTER UNIT - HIGH EFFICIENCY - Manual | priceindustries.com

«
...
36
37
38
39
40
...
»

Summary of Contents for FFU-HE Series

































































Reviews:

No comments

Related manuals for FFU-HE Series

Brand: NatureWater Pages: 10

Brand: Wayne Pages: 16

Aqua-Pure AP717

Brand: 3M Pages: 12

Aqua-Pure AP1610SS

Brand: 3M Pages: 2

AQUA-PURE IL-IM-01

Brand: 3M Pages: 2

Aqua-Pure AP200

Brand: 3M Pages: 2

Aqua-Pure AP510

Brand: 3M Pages: 16

High Flow Series

Brand: 3M Pages: 8

Brand: WaterLogic Pages: 69

Envirosolutions EnviroWash ES160P

Brand: Trimaco Pages: 4

TFP 16000 UV 13

Brand: T.I.P. Pages: 68

Brand: SMC Networks Pages: 33

Brand: Hoshizaki Pages: 2

Brand: Weq Pages: 2

Sterilight S12Q

Brand: R-Can Pages: 20

Brand: Suez Pages: 48

Brand: FILTRABOX Pages: 24

Brand: JRC Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands