Price FFU-HE Series Manual Download Page 33

Page: 33 / 64

MBAS/FBAS Pressure Switch Diagram

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Motor/Filter Indicator BAS (MBAS/FBAS)

Sample line string below:

FFU-HE/24/48/RSR/BC/ECM/115/10//CT//HEPA//ECMDX//WK/DSW/PC/TMB/ATS/

MBAS

FBAS

/WPF/PL-AL/F-AL/PL-B12/

F-B12

Operation

Option

Code

Action

Notes

Motor BAS

MBAS

Troubleshoot

Motor

Closes a dry contact to let the BAS signal pass through when the static

pressure is less than 0.2" w.g. indicating the motor is not operating.

Filter BAS

FBAS

Change

Filter

Closes a dry contact to let the BAS signal pass through when the static
pressure is greater than the calibrated pressure drop (factory set at 1.5x
clean filter).

Unit will come factory calibrated; no additional field modifications are required.

Wire unit terminal block according to wiring diagrams found starting on page 51 of this manual.

NOTE:

Wiring should be carried out by a certified electrician and meet national and local electrical codes.

FFU-HE

Pressure switch(es) completes signal when

failure is reached (as per chart above)

BAS Signal In

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

Summary of Contents for FFU-HE Series
































































Search results

Summary of Contents for FFU-HE Series

Reviews:

Related manuals for FFU-HE Series

Brands by name

Popular brands

Price FFU-HE Series, Manual

Search results

Summary of Contents for FFU-HE Series

Reviews:

Related manuals for FFU-HE Series

Brands by name

Popular brands