Price FFU-HE Series Manual Download Page 44 | Manualshive

Page: 44 / 64

background image

FAN FILTER UNIT - HIGH EFFICIENCY

INSTALLATION & SERVICE INSTRUCTIONS

Static Pressure Port

Bench Top Replaceable (BTR) Port

NOTE:

Sample line string below:

1//FFU-HE/24/48/

BTR

/BC/ECM/115/10//CT//HEPA//ECMDX//WK/DSW/PC/TMB///ML/FL/WPF/PL-AL///PL-MILL//

NOTE:

Safety cables will be attached to the diffuser face, but care should be taken to ensure that diffuser face does not swing and

injure anyone.

STEP 1:

Remove gasketed bolt located along center channel of BTR filter. There are two ports located on the face; either can be

used.

STEP 3:

Insert pressure measuring gauge (eg. Magnehelic) to read pressure drop across filter. Hole size is 5/16”.

NOTE:

Static Pressure Port can also be used as a test port for sample aerosol concentrations upstream of the filter.

42

priceindustries.com | FAN FILTER UNIT - HIGH EFFICIENCY - Manual

FAN FILTER UNIT - HIGH EFFICIENCY - Manual | priceindustries.com

«
...
42
43
44
45
46
...
»

Summary of Contents for FFU-HE Series

































































Reviews:

No comments

Related manuals for FFU-HE Series

Brand: Quooker Pages: 16

Brand: NatureWater Pages: 16

Brand: Patton Pages: 4

wavebrite SMART

Brand: Wave Pages: 10

Brand: Toro Pages: 12

Aqua-Pure APIL3

Brand: 3M Pages: 8

2CB5-S Replacement Cartridge EV9617-22

Brand: Everpure Pages: 2

Brand: Toro Pages: 28

Brand: Softena Pages: 48

Brand: Crystal Quest Pages: 2

Thunder Reverse Osmosis

Brand: Crystal Quest Pages: 6

Brand: Crystal Quest Pages: 8

Brand: Crystal Quest Pages: 9

Brand: Crystal Mountain Pages: 4

Brand: Ecosoft Pages: 104

Brand: Beko Pages: 32

Brand: Beko Pages: 30

Brand: Beko Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands