background image

AdvAntAge - digitAl vAv diffusers

DISPLAY NAVIGATION

18

ACUTHERM ADVANTAGE - Manual 

  |   

acutherm.com

vvt Menu 

Pressure Dependent Mode

Scroll through with 

Up

 and 

Down

 buttons, press 

Menu

 button to apply your changes *---wait---* will display as changes are applied.

vvt

dPr. COOl Min* 

0%

Cool Min flow

 · Cool Min Flow in %
 · Range: 0-100% Default: 0%

dPr. COOl MAX.* 

100%

Cool Max flow

 · Cool Min Flow in %
 · Range: 0-100% Default: 100%

dPr. HeAt Min* 

0%

Heat Min flow

 · Heat Min Flow in %
 · Range 0-100% Default: 0%

dPr.HeAt MAX* 

100%

Heat Max flow

 · Heat Max Flow in %
 · Range 0-100% Default: 100%

dPr. neutrAl 

0%

neutral flow

 · Sets the neutral flow
 · Range 0-100% Default: 0%

unOCC dPr POs* 

0%

unocc dpr Pos

 · When Advantage is unoccupied damper will ‘rest’ at this position
 · Range: 0-100% Default: 0%

inlet siZe* 

10 inCHes

inlet size

 · Size of the diffuser inlet (factory set)

K fACtOr* 

1500

K factor

 · If no DMS flow option is present, item will not display
 · Air flow calibration factor see DMS manual for more details

Air flOW* 

200 cfm

Air flow Measurement

 · If no DMS flow option is present, item will not display
 · If DMS flow option is present, LCD will display air flow rate

flOW units* 

cfm

Air flow Measurement

 · If no DMS flow option is present, item will not display
 · Units of measure for air flow adjustable to ‘cfm’, ‘l/s’, or ‘cmh’

Press Menu 

tO eXit

exit –

 

This will exit the info menu if you select Yes 

Note: Info menu will automatically time out after 60 seconds

*

Also available over BACnet network if diffuser has BACnet option installed.

Summary of Contents for Acutherm Advantage Master







































Reviews: