background image

IV

V676

®

 CONTROL CONSOLE INSTALLATION & OPERATION MANUAL

Compliance and Safety Notice

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 

1)

This device may not cause harmful interference, and 

2)

This device must accept any interference received, including interference that may cause undesired operation.

It is extremely important to read ALL safety information and instructions provided in this manual and any 
accompanying documentation before installing and operating the products described herein.  Heed all cautions and 
warnings during installation and use of this product.

Safety symbols used throughout this manual are as follows:

UNIVERSAL VOLTAGE RANGE: 100-240 VAC, 50/60 Hz, 10A Max

MAXIMUM AMBIENT TEMPERATURE: T

A

 = 50° C

NOT FOR RESIDENTIAL USE

DRY LOCATIONS ONLY

WARNING!

 Hazard of electrical shock. Disconnect power before servicing. Service and maintenance should 

be performed only by qualified personnel as determined by PRG. Refer to service manual before operating 
or servicing.

WARNING!

 Power supply plug and/or power switch/circuit breaker shall remain readily operable.

WARNING!

 For personal safety, this equipment must be properly grounded.

Do not, under any circumstances, cut or remove the ground prong from the power cord.

The power cord of this equipment is provided with a 3-prong grounding plug which mates with a standard 3-
prong grounded wall outlet to minimize the possibility of electric shock hazard from this equipment.

Have the wall outlet and electrical circuit checked by a qualified electrician to ensure the outlet is properly 
grounded. If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it 
replaced with a properly grounded 3-prong outlet.

Never unplug the equipment by pulling on the power cord. Always grip the plug firmly and pull it straight out 
from the outlet. Do not use a cord that shows cracks or damage along its length or at either end. 
Replacement cords may be ordered from PRG.

CAUTION

 advising of potential damage to product.

WARNING

 advising of potential injury or death to persons.

3077774

Summary of Contents for V676

































Reviews: