Precor M8.2E Owner'S Manual Download

Page: 41 / 43

Owner’s Manual Addendum

This addendum accompanies your

M8.2E/L Personal Recum-

bent Cycle Trainer Owner’s Manual and provides information
about changes to the hardware kit and assembly instructions.

Personal Recumbent
Cycle Trainer

The lockwashers used in the seat assembly have been
replaced with locknuts and a box wrench to help fasten the
seat more securely onto the seat base support. Diagram 1
shows the new hardware kit. Make sure that you have the
following items:

(A) four bolts—seat assembly

(B) two bolts—electronic console display assembly

(D) one 3/8" hex key

(E) four locknuts—seat assembly

(F) one box wrench—seat assembly

If any items are missing, contact the dealer from whom
you purchased the cycle or call 1-800-4-PRECOR for the
authorized Precor dealer nearest you.

Diagram 1

M8.2ELR hardware kit.

Summary of Contents for M8.2E












































Search results

Summary of Contents for M8.2E

Reviews:

Related manuals for M8.2E

Brands by name

Popular brands

Precor M8.2E, Owner'S Manual

Search results

Summary of Contents for M8.2E

Reviews:

Related manuals for M8.2E

Brands by name

Popular brands