manualshive.com logo in svg

Pramac GA20000, Owner'S Manual, Page: 5 / 48

Share
Download
Pramac GA20000 Owner'S Manual Download Page 5

Owner’s Manual for 50 Hz Air-Cooled Generator Sets

v

Section 1: Safety Information

Introduction ..........................................................1

Read This Manual Thoroughly  ....................................1

Safety Messages ..................................................1

Safety and Informational Decals  ........................2

Safety Rules  .........................................................5

General Safety  ............................................................5
Installation  ...................................................................6
Operation .....................................................................7
Maintenance ................................................................7

Hot Surfaces .........................................................9

Section 2: General Information

Generator Set ..................................................... 11

Data Decals  ........................................................12

Specifications  ....................................................13

Generator Set ............................................................13
Engine  .......................................................................14

Protection Systems  ...........................................14

Emissions ...........................................................14

Fuel Requirements  ............................................15

BTU Content ..............................................................15

Battery Requirements  .......................................15

Battery Charger ..................................................15

Engine Oil Requirements  ..................................15

Activating the Generator Set  ............................15

Wi-Fi Module  ......................................................15

Replacement Parts  ............................................16

Accessories........................................................ 16

Section 3: Operation

Site Prep Verification .........................................17

Generator Set Enclosure ...................................17

Opening the Lid  .........................................................17

Generator Main Line Circuit Breaker  ...............17

LED Indicator Lights  ..................................................17

Control Panel Interface  .....................................18

Using the Control Panel Interface  ....................18

Interface Menu Displays  ................................... 18

The LCD Panel ..........................................................18
Menu System Navigation  ..........................................19

Setting the Exercise Timer  ............................... 21

Emergency Stop  ................................................ 21

Operating Modes  ............................................... 21

Manual .......................................................................21
Auto ...........................................................................21
Exercise .....................................................................22

Manual Transfer Operation ............................... 22

Transfer to Generator Set Power Source ..................22
Transfer to Mains Power Source ...............................22

Automatic Transfer Operation  ......................... 23

Automatic Sequence of Operation  .................. 23

Mains (Utility) Power Failure  .....................................23
Cranking  ....................................................................23
Cold Smart Start ........................................................23
Cleaning Cycle  ..........................................................23
Load Transfer  ............................................................23

Shutting Generator Set Down While Under Load 
Or During A Mains Power (Utility) Outage  ...... 23

Section 4: Maintenance

Maintenance ....................................................... 25

Prepare Generator Set for Maintenance .......... 25

Generator Set Enable/Disable Procedure  .................25
Enclosure Panel Removal  .........................................25
Front Access Panel Removal  ....................................25
Intake Side Panel Removal  .......................................26

Performing Scheduled Maintenance  ............... 26

Service Schedule ............................................... 27

Maintenance Log .......................................................28

Checking Engine Oil Level  ............................... 29

Engine Oil Requirements .................................. 29

Required Oil  ..............................................................29

Changing the Oil and Oil Filter ......................... 29

Servicing the Air Cleaner .................................. 30

Spark Plugs ........................................................ 30

Checking and Adjusting Valve Clearance ....... 30

Checking Valve Clearance  ........................................30
Adjusting Valve Clearance  ........................................31

Table of Contents

Summary of Contents for GA20000

















































Reviews:

No comments