background image

 

1-5. Maintenance, service and faults 

 

The UPS system operates with hazardous voltages. Repairs may be carried out only 
by qualified maintenance personnel. 

 

Caution - 

risk of electric shock. Even after the unit is disconnected from the mains 

(building wiring outlet), components inside the UPS system are still connected to the 
battery and electrically live and dangerous. 

 

Before carrying out any kind of service and/or maintenance, disconnect the batteries 
and verify that no current is present and no hazardous voltage exists in the terminals 
of high capability capacitor such as BUS-capacitors. 

 

Only persons are adequately familiar with batteries and with the required 
precautionary measures may replace batteries and supervise operations. 
Unauthorized persons must be kept well away from the batteries. 

 

Caution - 

risk of electric shock. The battery circuit is not isolated from the input 

voltage. Hazardous voltages may occur between the battery terminals and the 
ground. Before touching, please verify that no voltage is present! 

 

Caution 

- Do not dispose of batteries in a fire. The batteries may explode.  

 

Caution

 - Do not open or mutilate batteries. Released electrolyte is harmful to the 

skin and eyes. It may be toxic. 

a)

 

Batteries may cause electric shock and have a high short-circuit current. Please 
take the precautionary measures specified below and any other measures 

necessary when working with batteries: Remove watches, rings, or other metal 
objects. 

b)

 

Use tools with insulated handles. 

c)

 

Wear rubber gloves and boots. 

d)

 

Do not lay tools or metal parts on top of batteries. 

e)

 

Disconnect charging source and load prior to installing or maintaining the 
battery. 

f)

 

Remove battery grounds during installation and maintenance to reduce 
likelihood of shock. Remove the connection from ground if any part of the 
battery is determined to be grounded. 

 

When changing batteries, install the same number and same type of batteries. 

Manufacture 

Type 

Rated 

Toplite (Guangzhou) 
Technology Battery Co Ltd 
(MH29104) 

NPW45-12 

12 V dc, 9.0 Ah 

UXW460-12 

12 V dc, 9.0 Ah 

NPW36-12 

12 V dc, 7.2 Ah 

UXW360-12 

12 V dc, 7.2 Ah 

NPW45-12 FR 

12 V dc, 7.0 Ah 

UXW460-12/FR 

12 V dc, 7.0 Ah 

NPW36-12 FR 

12 V dc, 7.0 Ah 

CSB Battery Co Ltd 

(MH14533) 

UXW360-12/FR 

12 V dc, 7.0 Ah 

GP1272 

12 V dc, 7.2 Ah 

UPS 12460 F2 

12 V dc, 9.0 Ah 

UPS 12360 6 

12 V dc, 6.5 Ah 

UPS 12360 7 

12 V dc, 6.5 Ah 

HR 1234W 

12 V dc, 8.5 Ah 

HR 1234W FR 

12 V dc, 8.5 Ah 

Yuasa Battery (Guangdong) 

Co Ltd (MH29616) 

NPW45-12 

12 V dc, 8.0 Ah 

NPW45-12FR 

12

 

 dc, 8.0 Ah 

 

 

 

Summary of Contents for VI TW 1.1K



















Reviews: