PowerTek MC642 Operation Manual Download | Manualshive

Page: 44 / 73

background image

:OUTPut:SWITching

Syntax:

:OUTPut:SWITching <CPD>
:OUTPut:SWITching?

Description:

If output amplitude is changed and output terminals are already switched on, some glitches
appear at output terminals. This setting allows selecting a method how new resistance at output
terminals is achieved.

Parameters:

<CPD>

{FAST|SMOoth|OPEN|SHORt} (default FAST)

·

FAST

new resistance is set as fast as possible

·

SMOoth

new resistance is set with minimal output changes

·

OPEN

open function is activated before new resistance is set

·

SHORt

short function is activated before new resistance is set

Remarks:

Overlapped command
Value is set according to “Startup” preset on restart and to default on *RST command

Example:

OUTP:SWIT FAST
OUTP:SWIT? Response: FAST

[:SOURce]:NICKel[:AMPLitude]

Syntax:

[:SOURce]:NICKel[:AMPLitude] <DNPD>[<UNIT>]
[:SOURce]:NICKel[:AMPLitude]?

Description:

This command sets temperature in Nickel mode. Node SOUR:NICK also selects “NICKEL”
function if not already selected. If unit parameter is part of temperature, new unit is set.

Parameters:

<DNPD>

temperature at Nickel function. Default value is 100.0 °C.

<UNIT>

{CEL|FAR|K}

·

CEL

degrees of Celsius

·

FAR

degrees of Fahrenheit

·

K

Kelvin

Remarks:

Overlapped command
Value is set according to “Startup” preset on restart and to default on *RST command

Example:

NICK 100.0
NICK? Response: 1.02 CEL

44

Operation manual

«
...
42
43
44
45
46
...
»

Summary of Contents for MC642










































































Reviews:

No comments

Related manuals for MC642

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands