PowerTek MC642 Operation Manual Download Page 39

Page: 39 / 73

*ESR?

Syntax:

*ESR?

Description:

This query returns the contents of the Event Status Register and clears the register.

Parameters:

<DNPD>

Event Status Register

Remarks:

Overlapped command

Example:

*ESR? Response: 0

*ESE

Syntax:

*ESE
*ESE?

Description:

This command programs the Event Status Enable register bits.

Parameters:

<DNPD>

Event Status Enable register, Range 0 … 255

Remarks:

Overlapped command

Example:

*ESE 2
*ESE? Response: 2

*CLS

Syntax:

*CLS

Description:

This command clears all status data structures in the device i.e. Event Status Register, Status
Byte Register except the MAV bit, Operation Status Register, Questionable Status Register.
Also error queue is cleared. Output queue is unaffected.

Parameters:

None

Remarks:

Overlapped command

Example:

*CLS

Operation manual

Summary of Contents for MC642










































































Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands

PowerTek MC642, Operation Manual

Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands