PowerTek MC642 Operation Manual Download Page 38

Page: 38 / 73

*RST

Syntax:

*RST

Description:

This command resets the device to its initial factory-set state. This state may be different from
the “Startup” preset.

Parameters:

None

Remarks:

Sequential command

Example:

*RST

*TST?

Syntax:

*TST?

Description:

This command launches internal self-test and returns result.

Parameters:

<DNPD>

0 – test passed, 1 – test failed

Remarks:

Sequential command

Example:

*TST? Response: 0

*STB?

Syntax:

*STB?

Description:

This query returns content of register STB, which carries the MSS bit status.

Parameters:

<DNPD>

Status byte register, Range 0 … 255

Remarks:

Overlapped command

Example:

*STB? Response: 0

*SRE

Syntax:

*SRE
*SRE?

Description:

This command allows set condition of the Service Request Enable register. Since bit 6 is not
used, the maximum value is 191.

Parameters:

<DNPD>

Service Request Enable register

Remarks:

Overlapped command

Example:

*SRE 2
*SRE? Response: 2

Operation manual

Summary of Contents for MC642










































































Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands

PowerTek MC642, Operation Manual

Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands