PowerTek MC642 Operation Manual Download Page 41

Page: 41 / 73

:CALibration:SECure:PASSword

Syntax:

:CALibration:SECure:PASSword <DNPD>

Description:

This command validates entered password and enables calibration access if verification is
successful. Access is invalidated after reset or if CAL:SEC:EXIT command is issued.
Calibration password can be changed from decade system menu

SETUP->Calibration-

>Change password.

Parameters:

<DNPD>

Range 0 ... 4294967295 (default 0)

Remarks:

Overlapped command

Example:

CAL:SEC:PASS 0

:CALibration:SECure:EXIT

Syntax:

:CALibration:SECure:EXIT

Description:

This command exits calibration mode and access.

Parameters:

None

Remarks:

Overlapped command

Example:

CAL:SEC:EXIT

:DISPlay:ANNotation:CLOCk:DATE:FORMat

Syntax:

:DISPlay:ANNotation:CLOCk:DATE:FORMat <CPD>
:DISPlay:ANNotation:CLOCk:DATE:FORMat?

Description:

This command sets format of date displayed on device screen.

Parameters:

<CPD>

{MDYS|MDYA|DMYS|DMYO|DMYA|YMDS|YMDO} (default MDYS)

MDYS

M/D/Y format

(M-month, D-day, Y-year)

MDYA

M-D-Y format

DMYS

D/M/Y format

DMYO

D.M.Y format

DMYA

D-M-Y format

YMDS

Y/M/D format

YMDO

Y.M.D format

Remarks:

Overlapped command
Value is not affected by reset or by *RST command

Example:

DISP:ANN:CLOC:DATE:FORM MDYS
DISP:ANN:CLOC:DATE:FORM? Response: MDYS

Operation manual

Summary of Contents for MC642










































































Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands

PowerTek MC642, Operation Manual

Search results

Summary of Contents for MC642

Reviews:

Brands by name

Popular brands