background image

GENERAL SAFETY

The PS19T and PS28T heaters are designed to take in cold water and heat it to temperatures 
suitable for normal domestic usage up to a maximum of 140 F(60 C). These models are not 
designed to be used as a sanitary booster which requires operating temperatures above 140 
F(60 C) or for any recirculating type applications. To obtain optimum performance and energy 
savings, these units should be located as near as possible to the point of use. 

The units is supplied with compression rings and nuts suitable for direct coupling to standard 
1/2” (5/8” outside diameter) copper piping. There is no need for additional screwed fittings and 
under no circumstances use a blow  torch on pipe while pipe is connected to the heater (serious 
damage to the electronic flow switch will result).

Also, ensure that the pipes are clear of installation debris before fitting the heater.

THE PS19T HEATER MUST HAVE

TWO DEDICATED INDEPENDENT 

CIRCUITS AND THE PS28T MUST HAVE

THREE DEDICATED 

INDEPENDENT 

CIRCUITS, USING CORRECTLY RATED WIRES AND 

CIRCUIT BREAKERS. 

WARNING

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE

DEATH, SERIOUS BODILY INJURY OR PROPERTY DAMAGE

. REFER TO 

THIS MANUAL FOR ASSISTANCE OR CONSULT THE LOCAL ELECTRIC UTILITY FOR 
FURTHER INFORMATION.

FAILURE TO 

GROUND

THE SYSTEM MAY RESULT IN DEATH OR SERIOUS INJURY.

WARNING

WARNING

WATER HEATERS EQUIPPED FOR ONE VOLTAGE ONLY:  

THIS WATER HEATER IS

EQUIPPED FOR ONE VOLTAGE TYPE ONLY: CHECK THE RATING PLATE ON THE FRONT 
COVER OF UNIT FOR THE CORRECT VOLTAGE. DO NOT USE THIS WATER HEATER WITH
ANY OTHER VOLTAGE OTHER THAN THE ONE SHOWN ON THE MODEL RATING PLATE.
FAILURE TO USE THE CORRECT VOLTAGE CAN CAUSE PROBLEMS WHICH CAN RESULT 
IN DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. IF YOU HAVE ANY 
QUESTIONS OR DOUBTS CONSULT CEC OR YOUR ELECTRIC COMPANY.

WARNING

HAZARD OF ELECTRICAL SHOCK! BEFORE REMOVING THE COVER OR SERVICING THE 
WATER HEATER, MAKE SURE THE ELECTRICAL SUPPLY TO THE WATER HEATER IS 
TURNED “OFF”. FAILURE TO DO THIS COULD RESULT IN

DEATH, SERIOUS BODILY INJURY,

OR PROPERTY DAMAGE

.

2

Summary of Contents for PS19T













Reviews: