manualshive.com logo in svg

Power Sensors Limited PQube 3, Instruction Manual

Share
Download
Power Sensors Limited PQube 3 Instruction Manual Download Page 90

PQube 3 Instruction Manual 

Page 90 of 103 

IP_Mask= 

IP_Gateway= 

IP_DNS1= 

IP_DNS2= 

information is ignored if DHCP is selected. 

[Email_Server_Settings] 

Set up the email account for your PQube 3 here.  

IMPORTANT

:

  Your PQube needs its own e-mail account. 

Do  not  assign  your  personal  email  account  to  your 
PQube – PSL is not liable for any loss of data.  All PQubes 
come with a free, temporary PQube.com e-mail account 
from  PSL.  Contact 

[email protected]

  for 

more information. 

 

 

POP_Email_Server_Address= 

POP_Email_Server_Port= 

Incoming_Email_Protocol= 

Incoming  email  server  settings.    Ask  your  IT 
administrator for this information. 

 

POP_Email_Server_Address= 
[mail.pqube.com] 

POP_Email_Server_Port=110 

Incoming_Email_Protocol=POP 

Incoming_Email_SSL_Encryption=OFF 

Toggle  SSL/TLS  encryption  while  retrieving  email 
commands 

ON 

OFF 

 

SMTP_Server_Address= 

SMTP_Server_Port= 

Outgoing  email  server  settings.    Ask  your  IT 
administrator for this information. 

 

SMTP_Server_Address= 
[mail.pqube.com] 

SMTP_Server_Port=25 

Outgoing_Email_SSL_Encryption=OFF 

Toggle SSL/TLS encryption while sending emails 

ON 

OFF 

 

PQube_Email_Account= 

PQube_Email_Password= 

IMPORTANT

:

  Your  PQube  needs  its  own  e-mail 

account. 

Do  NOT  assign  your  personal  e-mail  account  to 
your PQube. 

Your  PQube  automatically  clears  out  the  inbox 
after processing email commands. 

 

PQube_Email_Account= 
[email protected] 

PQube_Email_Password= 
p3001234 

Email_Address_Provider=PSL 

Use  pre-programmed  email  server  settings.    The 
server settings above do not need to be specified if 
using PSL, GMAIL, or NTT. 

PSL 

GMAIL 

 

Shop for Power Metering products online at:

1.877.766.5412

www.

PowerMeterStore

.ca

Summary of Contents for PQube 3








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands