background image

HELPLINE No. U K  0905-1460005 • IRELAND 1520-932626

WEB SUPPORT: www.heltec.eu

17

Charging the battery

Charging

Fig. G

The enclosed battery charger has been exclusively designed for loading
batteries of the PCC-1440.

Insert the battery (5) into the charger (11) as shown in the drawing. Take care
to observe the + and – polarity markings.

Plug the charger power plug into the power socket. The red quick-charge
lamp (12) illuminates.

Charging is completed once the green maintenance charge lamp (13) on the
other side of the charger illuminates. The battery is now ready for use.

The energy display (8) on the battery case provides information on the charge
level of the battery. Press the push button (14). 

The coloured display has the following meanings:

• All coloured bars illuminate (red-yellow-green): the battery is fully charged
• The red and yellow coloured bars illuminate: the battery is partially charged
• The red coloured bar illuminates: the battery is discharged and must be

recharged.

Only use the battery charger in a dry environment at a
temperature between 5 °C and 40 °C.

HELPLINE No. U K 0905-1460005 • IRELAND 1520-932626

WEB SUPPORT: www.heltec.eu

08

Safety instructions

f.  Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power
tool, taking into account the working conditions and the work to be
performed.

g. Damaged switches must be replaced at a customer service repair centre.

Do not use power tools that cannot be switched on and off.

h. Do not leave power tools unattended while they are switched on. Always

switch off the tool and wait until it has come to a full standstill before leaving.

i.

If the mains cable has been damaged, it must be replaced with a special
mains cable. These can be obtained from the manufacturer or the
manufacturer's customer service department.

5)  Battery use and care

a. Ensure the switch is in the off position before inserting battery pack.
b. Recharge only with the charger provided by the manufacturer. A charger

that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.

c. Take care that there are no metal objects (nails, paper clips, coins, etc.) in

contact with the surface of the battery.

d. If you come into contact with acid from the battery, rinse it off with water

immediately. If acid gets into your eyes, rinse out your eyes at once with
water and contact a doctor immediately!

6) Service

a. Please use a qualified expert who uses original replacement parts to repair

your power tool.

b. Caution! The use of any accessories or additional tools other than those

recommended in this manual may lead to an increased risk of injury. Only
use original replacement parts.

Summary of Contents for 14.4 Volt CORDLESS HAMMER DRILL













Reviews: