manualshive.com logo in svg

Potec PRK-8000, Operation Manual

Share
Download
Potec PRK-8000 Operation Manual Download Page 48

PRK-8000 Operation Manual

 

- 40 - 

7.2 Replacement

   

 

7.1.1 Printing Paper

   

 
Replace the roll of printing paper as soon as possible if the red line appears in the paper. 
 
(1)  Press the printer button to open the printer cover. 
(2)  Remove the used paper. 
(3)  Install a roll of new paper into the printer housing and close the printer cover. 
(4)  At this time, the printer detects the change of paper, and cuts the paper approximately 

‘2cm’ for initializing paper settings.(It takes about 3 seconds to complete.) 

 
 

7.1.2 Chin Rest Paper

   

 
(1)  Pull out the two pins on the chin rest. 
(2)  Insert the pins into the holes on the chin rest paper. More than 50 sheets of paper can 

be attached. 

(3)  Insert the pins straight into the holes on the chin rest. 
 
 

7.1.3 Fuses

   

 

(1)  Turn off the power. 
(2)  Remove the power cord from the electrical inlet. 
(3)  Insert flatblade screwdriver into notches in the fuseholder cover. Then turn the 

screwdriver countclockwise. 

(4)  Replace the fuses and reset the fuseholder cover in its original positions. 

Fuse rating: T3.15A 250V

 

 
 

7.3 Cleaning

   

 
(1)  Basically, keep this instrument clean. Don’t use volatile object, thinner or benzene, etc.   
(2)  Polish each part with a dry cloth containing detergent solution.   
 
 

7.4 When Moving the Instrument

   

 
(1)   Turn OFF the power switch. 
(2)   Disconnect the power cable. 
(3)   Close the stage holding dial in the clockwise direction. 
(4)   Move this machine holding the lower part of the mains to keep horizontally. 
 
 

Summary of Contents for PRK-8000





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands