manualshive.com logo in svg

Potec PRK-8000, Operation Manual

Share
Download
Potec PRK-8000 Operation Manual Download Page 13

PRK-8000 Operation Manual

 

- 5 - 

3.2 Operation Panel

  

 

 
 
 
 
 
 
 
 
 
 
 
 

 

      CHINREST 

LEVER 

                  Touch 

Button 

 

CHINREST 

LEVER 

This Lever is for raising/lowering the chin rest. Press “up” lever in order to raise and “down” 
lever to lower the chin rest. 

 

 

 

Press this button in order to change 
measurement mode. 

 

Press this button in order to enter 
DISPLAY Mode, where you can 
see measurement data stored in 
memory

 

 

 

Press this button in order to start manual 
or automatic measurement. 

- - 

 

 

Press this button in order to OFF/ON 
semi-automatic eye tracking 

Press this button in order to change 
CYL form. 

 

Press this button when the examinee’s 
eye is difficult to measure due to cataract 
or examinee with intraocular lens (IOL). 

 

Press this button in order to enter 
SIZE Mode, where you can measure 
the diameter of cornea, etc. 

 

Press this button in order to enter RET 
(Retroillumination) Mode, where you can 
observe the image obtained by 
retroillumination. 

 

Press this button to clear all stored 
data in memory. 

 

Press this button in order to print or 
transfer the measurement. 

 

Press this button in order to enter 
SETUP Mode, where you change all 
the settings about measurements, 
printouts etc. 

 
 

Summary of Contents for PRK-8000





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands