manualshive.com logo in svg

Potec PRK-8000, Operation Manual

Share
Download
Potec PRK-8000 Operation Manual Download Page 27

PRK-8000 Operation Manual

 

- 19 - 

5.4 Contact Lens Base Curve Measurement

  

[CLBC mode]

   

 
Base curve (posterior curve) of hard contact lens can he measured in the CLBC Mode. 
 
(1)    Enter CLBC Mode 

Press 

MODE button

 on the left side of the display, and then select “

CLBC

”. 

 
(2)  Attach Contact Lens. 

Put water in the concave section of contact lens holder at 
backside of the TEST Model Eye and place the contact lens on 
the holder with the concave surface facing upward. Contact 
lens is attached by surface tension. Take care that the contact 
lens is not attached inclined. Also, take care that there are no 
bubbles behind the contact lens. 

 
(3)    Attach the TEST Model Eye. 

Remove the chin rest paper. Fix the model eye attached with contact lens using pin. 
Place the contact lens to face the measurement window. 

 
(4)    Perform alignment and Focusing 

Align alignment marks and mire image. 
Then, focus on the mire image. 

 
(5)   Measurement 

Press the Measuring button . 
Measured results will be displayed on the monitor. 

 

 

 
(6)   Print 

Press the PRINT button. 

 
 

Summary of Contents for PRK-8000





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands