manualshive.com logo in svg

Potec PRK-8000, Operation Manual

Share
Download
Potec PRK-8000 Operation Manual Download Page 39

PRK-8000 Operation Manual

 

- 31 - 

6.5 SETUP Mode

   

 
Change all the settings about measurements, printouts etc. 
Press SETUP button in Measurement Mode. Setting item for REF/KER will be displayed. 
Press EXIT button in order to return to Measurement Mode. Some of the setting items 
consists of the two pages, the conversion page is available.   
 
(1)  

REF/KER

   

 

 

 

[How to change 

Setting Items

] 

Press one button on the left side of display. 

 

  [How to Change the Item] 
Pressing any button on display yields the selection of related item. 

 

  [How to Change the Contents] 
Press any un-pressed button on display. The selected button will be displayed in 
pressed button and the content will be changed. 

NOTE:    There are some contents to be changed in the other way. And such 

procedures will be instructed under the description of each item. 

 

  [How to Enter the Measurement Mode] 
Press EXIT button to quit the SETUP mode and enter the Measurement mode. 

 

 [Items for REF] 
VD    Vertex 

distance 

CYL     Cylinder form 
INC-R   Increment of sphere and cylinder 
D-SFT    Diopter Shift of Sphere 

        Press 

INC 

or 

DEC 

button 

to change the value of sphere by 0.12. 

S-SPD    Adjustment for Fogging speed   
PDSFT   Value Shift of Pupil Distance 

Press INC or DEC button to change the value of Pupil Distance

.

 

 

Change the Page 

PRINT Button 

Change the Item 

Summary of Contents for PRK-8000





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands