manualshive.com logo in svg

Potec PRK-8000, Operation Manual

Share
Download
Potec PRK-8000 Operation Manual Download Page 36

PRK-8000 Operation Manual

 

- 28 - 

(2) Ready for Observation 

Ask the examinee to look at the red roof of the eye fixation target. 
See procedure (3) of the Continuous Keratometry and Refractometry [K/R Mode]. 

 
(3) Observation 

z

  Adjust the amount of light of each light source so the image can be seen clearly. 

Press one of buttons for each light source on the side of display. The light source is 
adjustable from 0 to 100. If it is set to 0, the light turns off. 

¾

  RETRO LED:       The observation light source 

¾

  CHART LED:        Inside Fixed target light the patient sees 

¾

  EXTERNAL LED:    A light that turns around the eyes 

z

  Position the light for retroillumination reflected from cornea to a part that is not 

opaque by using the operation lever. If the light is directed from the edge of the pupil, 
it will be easier to observe the image. Focus on the image. 

z

  After confirming that the image is focused, press measuring button. The image will 

freeze. 

z

  Because the LED light in ILLUM mode is more brighter then normal measurement 

mode, if you observe a long period of time it can give stress in the eye of the 
examinee. 

z

  In the RETRO LED ON status, if there is no operation for more than 30 seconds, the 

RETRO LED will be OFF automatically. 

 
 
(4) Displaying of stored Image 

z

  Press DISP button in observation display. Images stored in memory will be 

displayed. 

 
[Menu Display] 

 

 
 
 
 
 
 
 
 
 
 
 
 

z

  When you press the Image button, selecting Image will be displayed. 

 
 

Images of eye 

Change Images
 of eye 

Serial number – Sub number 

Date &  Time of

the selected image

End of the  
Display Mode 

Clear stored Image 
& Measurement 
result 

Summary of Contents for PRK-8000





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands