background image

 

 

Part 15

USING THE TOUCH TERMINAL 

APPLICATION ENVIRONMENT 

It is 

very

 important that you check the following operational 

guidelines: 

Ventilation 

This terminal must 

NOT

 be operated in an environment with 

restricted ventilation. There must be at least 25 mm air clearance around any 
top or side ventilation holes with a free flow of air around the unit at 

ALL

 

times for the installation. 

Operating Environment 

The equipment must not be operated or stored in extremes of both 

temperature and humidity/moisture. (Operating range 5°C to 40°C and up to 
80% humidity – non condensing, max. wet bulb 26

°

C) 

UPS Battery (option) 

General care: 

The UPS battery is consumables beyond product warranty. Please 

definitely observe the alerts in beginning of this manual. If the equipment is to 
be  powered off for  more than few days, please always 

disconnect

 the battery 

from the system. Reconnect it and turn on the system to recharge the battery 
for 1 ~ 2 hours every 3 months for temperature lower than 30

°

C. Recharge for 

1 ~ 2 hours every month for temperature over 30

°

C. Temperature above 

40°C 

must be strictly avoided

 as it could cause termination of battery life and 

unexpected result even if the battery is not in work. The UPS battery can 
support basically the data preservation and smooth  running of the system 
during intermittent or few  minutes  (15 ~ 30 min. depending on loading and 
battery condition) power failure. 

Battery replacement: 

In the preloaded OS for a KS system, there is a built in utility Power 

Manager that will  interface the UPS battery  monitor status with user. When 
battery monitor disables the battery charging as designed while the UPS 
function of the system is originally  enabled, in other words the UPS battery is 
found out of order if actually installed,  there will be a popup message  as the 
picture at right asking the user to agree disabling the 
UPS function. The system will operate under 
deactivated UPS function no matter agreed or not. 
However, the monitoring goes on and the popup 
message will come back  on next system power up boot if not agreed. In any 
case, please replace the used up UPS battery at power off if the battery is well 
connected there but found inoperable by such messages. 

Summary of Contents for KS-6315





















Reviews: