background image

!

!

!

i

44

45

Wheels and tyres

The assembly consisting of the hub, spokes, tube  
protector and wheel rim is referred to as the wheel. 
The tyre is mounted on the rim and pressurised with  
a tube. To protect the tube against the sharp edges  
of the rim base or spoke nipples, it is lined with a tube 
protector.

After the first hours of use, the spokes and nipples 
may settle. Check the run-out of your wheels. If your 
wheels exhibit run-out, have them inspected or, if  
applicable, centred by a bike specialist or contact  
an authorised Porsche Centre or the Porsche Bike  
hotline.

If a tyre change is necessary, use original spare  
parts or tyres of exactly the same size. The size of 
your tyre is specified on the tyre sidewall, either in 
standard millimetres [ e.g. 52–622; 52 mm width  
when inflated and 622 mm [ inner ] diameter ] or in 
inches [ e.g. 28 x 2.0 ].

Adjusting the belt may differ from the method  
described here. Please consult the documentation 
provided by the belt manufacturer.

Risk of damage to the belt. 

Do not forcefully  

apply excessive pressure to the belt or use tools with 
sharp edges when working on the pulley. Do not twist 
the belt. Do not excessively bend or squeeze the belt. 
Observe the manufacturer instructions when handling 
the belt.

Sudden loss of power and propulsion. 

If the belt 

tension is insufficient, the belt may slip over the pulley 
and be damaged. The loss of power and propulsion 
may cause a crash. Have a bike specialist change and 
adjust the belt. 

Sudden restriction of the turning angle. 

Using 

tyres that are larger than the factory recommended 
size may result in contact between your foot and the 
front wheel when turning. There is a risk of crashing. 
Only mount tyres that correspond to the factory  
recommended size.

Overload due to incorrect tyre size. 

Using tyres 

that do not correspond to the factory recommended 
size may overload the frame and front fork. There  
is a risk of fracturing. Only mount wheels with the  
corresponding factory recommended size.

Tyres that are larger than the factory recom-
mended size may rub against the frame and front 
fork and damage the paint.

 Only mount wheels with 

the correct factory recommended size.

PLEASE NOTE

PLEASE NOTE

WARNING

WARNING

WARNING

INFORMATION

Derailleur

Summary of Contents for Bike RS












































Reviews: