background image

PH03 Comfort Inn - September 2008

Page 9 of 12

To mount the grab bars, pry back the two round snap lock fl anges on each grab bar with a screwdriver.  Align the three-
hole pattern on both fl anges of the grab bars to the holes on the support rails and rivet in place using (18) PC-000102 
rivets and (18) PC-000106 back-up washers.  

NOTE:  

(You may have to re-drill some holes to bring them into alignment 

due to manufacturing tolerances.)  

Step 7.     Mounting the Grab Bars

PC-000102 Rivet

    18 Used in this step

PC-000106 Washer

 18 Used in this step

Each of the three sidewall panels has two vent 
screens.  On the surface of each screen there 
is a date stamp symbol.  The symbol goes to-
ward the center of the sidewall panel, facing 
the inside

.  For each of the sidewalls, insert 

into the vent slot one screen from each 
side and overlap the center holes of the 
screens 

(at the date stamp symbol).  

IMPOR-

TANT - 

MAKE SURE BOTH SCREENS ARE 

CENTERED IN THE VENT SLOT.  

From inside 

the unit using a 13/64” drill bit, drill a hole 
through the center hole of the screen and 
into each of the side walls.  From the out-
side rivet a PC-000100 rivet into the center 
hole with a PC-000106 back-up washer on 
the inside.  From inside the unit using the 
holes at the ends of the screens as guides, 
drill holes through to the wall panels.  From 
the outside rivet the screens in place with 
PC-000100 rivets and PC-000106 back-up 
washers on the inside.  

Step 8.     Fly Screen Installation

PC-000100 Rivet 

   9 Used in this step

PC-000106 Washer

9 Used in this step

Slide the vent stack up through the 4” hole of the roof and down into the corresponding hole in the tank.  Using a 
13/64” drill bit, drill a hole through the boss on the tank and through the vent stack.  Rivet into place with (1) PC-000117 
rivet.  

Step 9.     Vent Stack Installation

PC-000117 Rivet

 1 Used in this step

Summary of Contents for Comfort Inn PH03













Reviews: