background image

      

PM50/PM80 INSTALLATION MANUAL

 

  

 

 

                                            

 

10231-10.doc

Polyamp AB, Sweden 

www.polyamp.com 

Page 

2 (7) 

 
 

 

 

 

Warranty

 

All Polyamp DC/DC converters are warranted against defective material and 
workmanship. This warranty is valid for 24 months from the date of delivery. 
We will repair or replace products, which prove to be defective during the 
warranty period. The warranty is valid only if the converter is used within 
specification.  

 
 

Manual 

This manual is as complete and actual as possible at the time of printing. 
However, the information may have been updated since then. Polyamp AB 
reserves the right to make changes in this manual without notice. 

 
 
 
 

 

The exclamation point within an equilateral triangle is intended to alert the user to presence of 

important operating and maintenance instructions in the literature accompanying 

 
 
 
 

 

The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user 

to presence of uninsulated ”dangerous voltage” within the products enclosure that may be of 

sufficient magnitude to constitute a risk of electric shock to persons 

 
 
 
 

Caution! 

To prevent the risk of electric shock, do not open enclosure. No serviceable parts inside. Refer 
servicing to qualified service personnel only 
 

Summary of Contents for PM50








Reviews: