background image

12

13

Polk Customer Service 800-377-7655 (Outside USA & Canada: 410-358-3600)

Customer Service Hours of Operation: Monday-Friday, 9am-5:30pm est           [email protected]

What if my provided optical cable is too short?

• 

We did our best to provide a cable of  

  adequate length; however, there might  
  be a few setup instances in which the  
  cable may be too short. If that is your  
  situation, your local electronics store  
  will have cables that meet your  
  required length.

My audio sounds strange and distorted.

• 

Your SurroundBar 2000 requires a clean,  

  unaltered stereo signal for proper audio  
  performance. If the sound from your  
  SurroundBar 2000 is strange or distorted,  
  then check the audio menus of whatever  
  source(s) are connected to your SurroundBar  
  2000 and make sure any audio processing  
  is turned off.

Why can’t I successfully program  
the SurroundBar 2000 to respond  
to my remote control?

• 

There are many remote control formats,  

  and we have done our best to make the  
  SurroundBar 2000 compatible with the  
  most popular brands. However, there  
  are likely some cases in which the bar  
  will not be able to learn your remote codes. 

• 

In this case, please use the remote control  

  provided with the SurroundBar 2000 product  
  or try a different universal remote control.

Note:

 RF only remotes will not work  

with this system.

How do I control the SurroundBar 2000?

 

There are three ways to control your  
SurroundBar 2000: 

• 

Use the buttons on the front of the bar.

• 

Use the provided remote control. 

• 

Program the SurroundBar 2000 to  

  respond to your existing remote  
  (see included instructions).

My SurroundBar 2000 was responding  
to commands, but now it isn’t. What  
should I do?

• 

In this rare event, simply turn off the power  

   

(switch located on the back of the bar),  

   

wait a few seconds, and then turn the  

   

power back on. This should restore  

  

control.

How do I erase previously learned remote  
control commands?

• 

If you have programmed your SurroundBar  

   

2000 to respond to a remote control and  

   

you no longer want it to do so, then you  

   

can erase the codes by pressing the  

   

LEARN key for about two seconds while  

   

the unit is in standby mode (power LED  

   

is red). The SurroundBar 2000 will  

   

continue to respond to the provided  

   

credit card remote control.

To contact Customer Service/ 
Technical Support:

• 

If you have a question or comment, please  

   

feel free to call us or email us. In North  

   

America and Canada, call Polk Customer  

   

Service: 800-377-7655 (M-F 9-5:30 EST)  

   

or via email [email protected].  

   

Outside the US, call 410-358-3600.

Polk is a DEI Holdings, Inc. Company. Polk  
and SurroundBar are registered trademarks  
of Polk Audio, Inc. 

Products that have earned the Energy Star

®

  

are designed to protect the environment  
through superior energy efficiency. 
 
               is a trademark of SRS Labs, Inc.  
TruSurround HD technology is incorporated  
under license from SRS Labs, Inc.

Limited Warranty

Polk Audio, Inc., warrants to the original retail purchaser 
only. This warranty will terminate automatically prior to 
its stated expiration if the original retail purchaser sells 
or transfers the Product to any other party. Polk Au-
dio, Inc., warrants, to the original retail purchaser only, 
that the LOUDSPEAKER(S), PASSIVE CROSSOVER 
COMPONENT(S) and ENCLOSURE on this Polk Audio 
Loudspeaker Product will be free from defects in material 
and workmanship for a period of three (3) years from the 
date of original retail purchase from a Polk Audio Authorized 
Dealer. Furthermore, Polk Audio, Inc., warrants, to the origi-
nal retail purchaser only, that any AMPLIFIER OR OTHER 
ELECTRONIC COMPONENT that may be included in this 
Polk Audio Loudspeaker Product will be free from defects  
in material and workmanship for a period of one (1) year 
from the date of original retail purchase from a Polk Audio 
Authorized Dealer. To allow Polk Audio to offer the best 
possible warranty service, please fill out the Product Reg-
istration Card(s) and send it to the Factory at the address 
provided on the Product Registration Card(s) within ten (10) 
days of the date of original purchase. Defective Products 
must be shipped, together with proof of purchase, prepaid 
insured to the Polk Audio Authorized Dealer from whom  
you purchased the Product, or to the Factory at 1 Viper 
Way, Vista, California 92081. Products must be shipped in 
the original shipping container or its equivalent; in any case 
the risk of loss or damage in transit is to be borne by you. 

If upon examination at the Factory or Polk Audio Autho-
rized Dealer it is determined that the unit was defective in 
materials or workmanship at any time during this Warranty 
period, Polk Audio or the Polk Audio Authorized Dealer will, 
at its option, repair or replace this Product at no additional 
charge, except as set forth below. All replaced parts and 
Products become the property of Polk Audio. Products 
replaced or repaired under this warranty will be returned to 
you, within a reasonable time, freight prepaid. This warranty 
does not include service or parts to repair damage caused 
by accident, disaster, misuse, abuse, negligence, inad-
equate packing or shipping procedures, commercial use, 
voltage inputs in excess of the rated maximum of the unit, 
cosmetic appearance of cabinetry not directly attributable to 
defect in materials or workmanship, or service, repair,  

or modification of the Product which has not been 
authorized or approved by Polk Audio. This warranty shall 
terminate if the serial number on the Product has been 
removed, tampered with or defaced.

This warranty is in lieu of all other expressed Warranties. 
If this Product is defective in materials or workmanship 
as warranted above, your sole remedy shall be repair or 
replacement as provided above. In no event will Polk Audio, 
Inc. be liable to you for any incidental or consequential 
damages arising out of the use or inability to use the 
Product, even if Polk Audio, Inc., or a Polk Audio Authorized 
Dealer, has been advised of the possibility of such dam-
ages, or for any claim by any other party. Some states do 
not allow the exclusion or limitation of consequential dam-
ages, so the above limitation and exclusion may not apply 
to you. All implied warranties on this Product are limited to 
the duration of this expressed Warranty. Some states do not 
allow limitation on how long an implied Warranty lasts, so 
the above limitations may not apply to you. This Warranty 
gives you specific legal rights, and you also may have other 
rights which vary from state to state.

This Warranty applies only to Products purchased in  
the United States of America, its possessions, and U.S.  
and NATO armed forces exchanges and audio clubs.  
The Warranty terms and conditions applicable to Products 
purchased in other countries are available from the Polk 
Audio Authorized Distributors in such countries.

Customer Service

Thank you for your Polk Audio purchase. If you have  
a question or comment, please feel free to call us or  
email us. In North America and Canada, call Polk Audio 
Customer Service 800-377-7655 (M-F, 9-5:30 EST)  
or via email [email protected]. Outside the US,  
call 410-358-3600.

Summary of Contents for SurroundBar 2000



















Reviews: