background image

 

Some jurisdictions do not allow the exclusion or limitations of incidental or 

consequential damages, so the above limitation or exclusion may not apply to you. 

This Limited Warranty gives you specific legal rights, and you may also have other 

rights that vary from jurisdiction to jurisdiction. 

FCC R

ADIO 

F

REQUENCY 

S

TATEMENT

 

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if 

not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference 

will not occur in a particular television reception (which can be determined by turning 

the equipment off and on), the user is encouraged to try to correct the interference by 

one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment to an outlet on a circuit different from that which the 

receiver is connected. 

 

Shielded interconnect cables and shielded power cord which are supplied 

with this equipment must be employed with this equipment to ensure 

compliance with the pertinent RF emission limits governing this device. 

 

Consult the dealer or an experienced radio/TV technician for help if the 

conditions persist. 

 

Changes or modifications not expressly approved by the manufacturer or 

authorized service center could void the user’s authority to operate this 

equipment. 

This device complies with Part 15 of the FCC Rules.  Operation is subject to the 

following two conditions: (1) this device may not cause harmful interference, and (2) 

this device must accept any interference received, including interference that may 

cause undesired operation. 
 
 

 

44

Summary of Contents for SmartOffice PN2040


















































Reviews: