Playnation Sweetwater II 2401 Manual Download Page 87

Page: 87 / 89

DETAIL B

GROUND STAKE

SCALE 1 : 11

SCREW AND WASHER

THAT COMES WITH

GROUND STAKE

CORNER POST

DETAIL A

SCALE 1 : 11

SWING LEG

SCREW AND WASHER THAT

COMES WITH GROUND STAKE.

GROUND STAKE

STEP 48: GROUND STAKES

1: PLACE THE GROUND STAKES ON THE OUTSIDE OF THE SWING LEGS AS SHOWN BELOW.

HAMMER A GROUND STAKE INTO THE EARTH NEXT TO EACH SWING LEG AT AN ANGLE.

DO NOT HOLD THE UPPER PORTION OF THE STAKE AFTER THE FIRST COUPLE OF HITS OR IT

MAY VIBRATE HARSHLY AGAINST YOUR HAND. IF THE TOP PART OF THE STAKE TWISTS

WHEN IT ENCOUNTERS A ROCK OR ROOT YOU MAY HAVE TO BEND THE TOP PORTION OF

THE STAKE AGAINST THE SWING LEG. FINALLY INSTALL THE SCREW AND WASHER.

2: ATTACH EACH GROUND STAKE TO THE SWING LEG WITH A #14 X 2" PAN HEAD SCREW

AND A 1/4" FENDER WASHER PROVIDED WITH THE GROUND STAKE.

3: HAMMER A GROUND STAKE ON THE INSIDE OF EACH CORNER POST. USE CAUTION

WHEN HAMMERING SO THAT YOU DO NOT MAR THE WOOD. DO NOT HOLD THE UPPER

PORTION OF THE STAKE AFTER THE FIRST COUPLE OF HITS OR IT MAY VIBRATE HARSHLY

AGAINST YOUR HAND. LEAVE THE TOP PORTION OF THE GROUND STAKE ABOVE THE

GROUND FAR ENOUGH SO THAT YOU CAN STILL GET THE SCREW INTO THE HOLE AT THE

TOP OF THE STAKE.

4: ATTACH EACH GROUND STAKE TO THE CORNER POST WITH A #14 X 2" PAN HEAD

SCREW AND A 1/4" FENDER WASHER PROVIDED WITH THE GROUND STAKE.

SWING LEGS

POSTS

CORNER

GROUND STAKE

Summary of Contents for Sweetwater II 2401


























































































Search results

Summary of Contents for Sweetwater II 2401

Reviews:

Related manuals for Sweetwater II 2401

Brands by name

Popular brands

Playnation Sweetwater II 2401, Manual

Search results

Summary of Contents for Sweetwater II 2401

Reviews:

Related manuals for Sweetwater II 2401

Brands by name

Popular brands