Planeta PKB Series Operation And Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 52

background image

19

4 Transport and Storage

Transport

If necessary, the hoist trolley unit can be transported to another location. To prevent damage while

transporting, follow the steps below.

‐

Lift the load hook to its highest position.

‐

Put the housing down on a stable underground.

‐

Fixate the chain. This can be achieved by tying the chain together or putting it in

a chain bag or box.

‐

Make sure the chain bag or box is fixated.

If the hoist trolley unit is transported over longer distances, follow the additional steps below.

‐

The hoist trolley unit shall be transported in a closed and/or sealed packing.

‐

Fixate the hoist trolley unit and its components to the transport packing.

‐

The hoist trolley unit shall be kept free from excessive vibrations.

Storage

To keep the hoist trolley unit in good condition while storing for a period longer than six months
follow the steps below.

Attention! If the hoist trolley unit is going to be stored for a period shorter than six

months read chapter 10 “Taking out of operation”.

‐

The hoist trolley unit may only be stored in unloaded condition.

‐

Perform routine maintenance and maintenance for storage. See chapter 8.1

“Maintenance schedule”.

‐

The environment should be clean and dry.

‐

If necessary, the hoist trolley unit shall be cleaned.

‐

The hoist trolley unit shall be kept free from excessive vibrations.

‐

The hoist trolley unit shall be protected against excessive water, wind and salt

‐

The hoist trolley unit shall be stored in a closed and/or sealed packing.

‐

Observe environmental protection laws (do not allow oil etc. to leak).

Model K

‐

Temperature not colder than -20°C or hotter than +40°C.

Model N

‐

Temperature not colder than -15°C or hotter than +40°C.

Sea fastening

An hoist trolley unit installed on a ship shall be sea fastened when necessary. Sea fastening is
fixating the hoist trolley unit to prevent movement which could result in a damage.

The following measures shall be taken:

‐

Fixate the hoist trolley unit and its components by lashing or other means.

‐

Lift the load hook to its highest position.

‐

Make sure the load and hand chain is not able to swing. This can be achieved by

tying the chain together or putting it in a chain bag or box.

‐

Make sure the chain bag or box is fixated.

Parking device

Standard headroom, low headroom and ultra low headroom hoist trolley units can optionally be
executed with a single side parking device or parking pin. A single sided parking device is operated
using a hand chain to press a locking disk against the monorail where a parking pin can be used to
fasten the trolley using a hole in the monorail.

19

«
...
17
18
19
20
21
...
»

Summary of Contents for PKB Series





















































Reviews:

No comments

Related manuals for PKB Series

Brand: Texas Pages: 38

Brand: RED ROOSTER Pages: 60

Brand: RED ROOSTER Pages: 64

Brand: RED ROOSTER Pages: 66

Brand: CM Pages: 4

Lodestar D8 PLUS

Brand: CM Pages: 12

Brand: CM Pages: 20

Brand: CM Pages: 32

Brand: CM Pages: 34

Brand: CM Pages: 48

Brand: CM Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands