manualshive.com logo in svg

Piusi MC BOX B.SMART, Installation - Use - Maintenance, Page: 10 / 48

Share
Download
Piusi MC BOX B.SMART Installation - Use - Maintenance Download Page 10

10 

/48

Installation, use and maintenance

M0583

MCBox ETL-

8 

DESCRIPTION OF THE MAIN PARTS

FOREWORD

B.SMART is an electronic system for controlling the dispensing of fluids via 

smartphone.

The control system consists of:

An electronic controller 

equipped with a BlueTooth interface (BLE 4.0 and later), a display and an 

interface LED that controls a dispensing pump

An APP

installed on a smartphone equipped with an Android operating system or 

Apple IoS 

A WebAPP 

namely an internet portal accessible from any PC or Tablet connected to the 

internet from which the entire site can be monitored 

SYSTEM FUNCTIONS 

• 

site configuration, acquisition and management of refillings, 

management of refilling fuel dispensers, management of drivers, 

vehicles and detailed reporting of the dispensings via WebAPP 

accessible from any PC/Tablet, using your credentials

• 

Fuel dispensing using the dedicated APP: PIUSI APP, downloadable 

only for smartphones from Play Store and App Store, which connects to 

the fuel dispenser / controller via BLE connection 

• 

Fuel dispensing using the dedicated APP also in areas without 3/4G 

coverage and Wi-Fi

• 

Dispensing via iButton associated with the individual driver

• 

Possibility to remotely manage sites far from the company headquarters

Summary of Contents for MC BOX B.SMART

















































Reviews:

No comments