background image

15

EN

EN

G

LI

SH

GRILL TEMPERATURE RANGES

Temperature readouts on the control board may not exactly match the thermometer. All temperatures listed below
are approximate and are affected by the following factors:outside ambient temperature, the amount and direction of
wind, the quality of pellet fuel being used, the lid being opened, and the quantity of food being cooked.

HIGH TEMPERATURE(205-260°C / 401-500°F)

This range is best used to sear and grill at a high heat. Use in tandem with the Flame Broiler (slide plate) for indirect or
direct flame cooking. With the

Flame Broiler open

, direct flame is used to create those “blue” steaks, as well as flame-

kissed vegetables, garlic toast or s’mores! When the

Flame Broiler is closed

, the air circulates around the barrel, resulting

in convection heat. High temperature is also used to preheat your grill, burn-off the cooking grids, and to achievehigh heat
in extreme cold weather conditions.

MEDIUM TEMPERATURE(135-180°C/ 275-356°F)

This range is best for baking, roasting, and finishing off that slow smoked creation. Cooking at these temperatures will
greatly reduce the chances of a grease flare-up. Ensure that the Flame Broiler Slider in the closed position, covering the
slotted openings.Great range for cooking anything wrapped in bacon,or where you want versatility with control.

LOW TEMPERATURE(82-125°C / 180-257°F)

This range is used to slow roast, increase smoky flavor, and to keep foods warm. Infuse more smoke flavor and keep your
meats juicy by cooking longer at a lower temperature (alsoknown as

low and slow

). Highly recommended for the big turkey

at Thanksgiving, juicy ham at Easter,or the huge holiday feast.

Smoking is a variation on true barbecuing and is truly the main advantage of grilling on a wood pellet grill.

Hot smoking

,

another name for

low and slow

cooking, is generally done between 82-125oC/ 180-257oF.Hot smoking works best when

longer cooking time is required, such as large cuts of meats, fish, or poultry.

TIP:To intensify that savory flavor, switch to a low temperature range immediately after putting your food on the
grill. Thisallows the smoke to penetrate the meats.

Thekey is to experiment with the length of time you allow for smoking,before the mealis finished cooking.Someoutdoor chefs
prefer to smoke at the end of a cook, allowing the food to keep warm until ready to serve.Practicemakesperfect!

Summary of Contents for PB1600PS1






























Reviews: