Piper Arrow IV Maintenance Manual Download

Page: 362 / 752

32-00-02

Page 32-04

December 1, 1978

2D11

CHART 3201. TROUBLESHOOTING (LANDING GEAR) (cont.)

Red gear unsafe light

Light circuit wire loose.

Check wiring.

operates on and off after
gear has retracted.

Hydraulic system losing

Refer to Hydraulic System,

pressure.

Chapter 29.

Gear up switch out of

Check gear up adjustment

adjustment.

and then switch adjustment.

Red gear unsafe light out

Lamp burned out.

Replace lamp.

and one green gear down
light out though gear is

Gear down limit switch

Replace switch.

down and locked.

failed.

—NOTE—

Light circuit wire broken.

Check wiring.

Ascertain navigation lights
are off (daytime).

Red gear unsafe light and

Indicator lights circuit

Reset circuit breaker and

all green lights out.

breaker open.

determine cause for open
circuit breaker.

—NOTE—

Light circuit wire broken.

Check wiring.

Ascertain navigation lights
are off (daytime).

Red gear unsafe light and

Landing gear selector circuit

Rest circuit breaker and

horn fail to operate when

breaker open.

determine cause for open

throttle is near closed and

circuit breaker.

landing gear is retracted.

Micro switch at throttle out

Adjust micro switch.

of adjustment.

Micro switch at throttle

Replace switch.

failed.

Warning horn and light

Check wiring.

circuit wire broken.

Trouble

Cause

Remedy

PIPER AIRCRAFT

PA-28RT-201 / 201T

MAINTENANCE MANUAL

Summary of Contents for Arrow IV

















































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Arrow IV

Reviews:

Related manuals for Arrow IV

Brands by name

Popular brands

Piper Arrow IV, Maintenance Manual

Search results

Summary of Contents for Arrow IV

Reviews:

Related manuals for Arrow IV

Brands by name

Popular brands