Piper Arrow IV Maintenance Manual Download | Manualshive

Page: 179 / 752

background image

BATTERY REMOVAL AND INSTALLATION (NARCO). (Refer to Figures 23-1 and 23-2.)

1. Set the ON/OFF/ARM switch on the transmitter to OFF.
2. Disconnect antenna coaxial cable from ELT.
3. Remove ELT from its mounting bracket by releasing the latch on the strap and sliding the ELT off the

bracket.

4. Extend the portable antenna.
5. Unscrew the four screws that hold the control head to the battery casing and slide apart.
6. Disconnect the battery by unsnapping the snap-off battery pigtail terminals from the bottom of the

transmitter printed circuit board.

7. Discard old battery pack. (DO NOT EXPOSE TO FLAME.)

—CAUTION—

The battery pack is shipped with a sealant on the inside lip so that
a water tight seal will be retained. DO NOT REMOVE THIS
SEALANT.

8. Connect new battery pack terminals to the bottom of the circuit board.
9. Reinsert the control head section into the battery pack being careful not to pinch any wires, and replace

the four screws. If the four holes do not line up, rotate the battery pack 180° and reinsert.

10. Slide the portable antenna back into the stowed position.
11. Place transmitter into its mounting bracket and fasten the strap latch.
12. Connect the antenna coaxial cable to the ELT and ensure that the contact separator is inserted between

the antenna contact finger and the portable antenna. (Refer to Figure 23-2.)

13. Press RESET button and set ON/OFF/ARM switch to ARM.
14. Make an entry in the aircraft logbook, including the new battery expiration date.
15. A unit operational check may now be performed on the ELT. (Refer to Testing Emergency Locator

—NOTE—

Inspect the external whip antenna for any damage. Av o i d
bending the whip. Any sharply bent or kinked whip should be
replaced. Antenna damage may cause structural failure of whip
in flight.

23-10-03

Page 23-02

Added: July 24, 1981

1H11

PIPER AIRCRAFT

PA-28RT-201 / 201T

MAINTENANCE MANUAL

«
...
177
178
179
180
181
...
»

Summary of Contents for Arrow IV

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Arrow IV

Brand: Nova Pages: 22

Brand: ICP Pages: 17

Brand: Gulfstream Pages: 94

1978 AA 5A CHEETAH

Brand: Gulfstream Aerospace Pages: 190

Brand: SKY PARAGLIDERS Pages: 32

Brand: MAC PARA Pages: 40

2018 DOUBLE AGENT

Brand: Cabrinha Pages: 10

Brand: Van's Aircraft Pages: 50

Brand: Mooney Pages: 227

Brand: Diamond Aircraft Pages: 24

Brand: DUC Hélices Pages: 27

Sonar Foil System 2020

Brand: North Kiteboarding Pages: 11

Brand: Rotax Pages: 80

SEMINOLE PA-44-180

Brand: Piper Pages: 881

Brand: HQ-Powerkites Pages: 17

Brand: GRAVITY Pages: 37

Brand: GRAVITY Pages: 42

Brand: CrazyFly Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands