manualshive.com logo in svg

Piper Arrow IV, Maintenance Manual, Page: 289 / 752

Share
Download
Piper Arrow IV Maintenance Manual Download Page 289

LIST OF ILLUSTRATIONS 

(cont)

FIGURE NO.

SUBJECT

GRID NO.

21-17.

Condenser Air Scoop Installation

1G14

21-18.

Expansion Valve

1G15

21-19.

Components Installation

1G17

21-20.

Adjustment of Air Conditioning Throttle Switch

(PA-28RT-201)

1G17

21-21.

Air Conditioning Wiring Schematic

1G19

23-1.

ELT Portable Folding Antenna (Narco)

1H12

23-2.

ELT Using Fixed Aircraft Antenna (Narco)

1H12

23-3.

ELT Schematics

1H16

24-1.

Lamp-Bank Load

1I8

24-2.

Exploded View of Alternator (Chrysler)

1I10

24-3.

Checking Field Coil Current Draw

1I10

24-4.

Testing Field Circuit

1I10

24-5.

Testing Positive Rectifiers With C-3829 Tester

1I12

24-6.

Testing Negative Rectifiers With C-3829 Tester

1I12

24-7.

Rectifier End Shield and Stator Assembly

1I12

24-8.

Testing Positive Rectifiers With Test Lamp

1I14

24-9.

Testing Negative Rectifiers With Test Lamp

1I14

24-10.

Rectifier and Heatsink Assembly Removal

1I14

24-11.

Rectifier End Shield Assembly

1I14

24-12.

Testing Stator

1I16

24-13.

Removal of Pulley

1I16

24-14.

Removal of Bearing

1I16

24-15.

Removal of Rectifier End Shield Bearing

1I16

24-16.

Testing Rotor for Ground

1I17

24-17.

Testing Rotor for Opens or Shorts

1I17

24-18.

Installation of Grease Retainer

1I18

24-19.

Installation of Rectifier End Shield Bearing

1I18

24-20.

Installation of Drive End Shield Bearing

1I18

24-21.

Installation of Pulley

1I18

24-22.

Installation of Insulators

1I20

24-23.

Installation of Positive Rectifier Assembly

1I20

24-24.

Installation of Capacitor

1I20

24-25.

Installation of Battery Output Insulator

1I20

24-26.

Installation of Negative Rectifier Assembly

1I21

24-27.

Installation of Stator

1I21

24-28.

Exploded View of Alternator (Prestolite)

1I23

24-29.

Removal of Slip Ring End Bearing

1I24

24-30.

Removal of Rectifier

1I24

24-31.

Removal of Drive End Head

1J2

24-32.

Removal of End Head Bearing

1J2

24-33.

Testing Rotor for Ground

1J2

24-34.

Testing Rotor for Shorts

1J2

Introduction

Page - 9

Revised: July 13, 1983

2A10

PIPER AIRCRAFT

PA-28RT-201 / 201T

MAINTENANCE MANUAL

Summary of Contents for Arrow IV

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments