Pioneer VSX-LX503 Instruction Manual Download Page 156

Page: 156 / 174

156

≫

≫

≫

≫

≫

≫

• If you have terminated the Initial Setup halfway, turn this unit to standby mode.

Then turning the power on again can display the Initial Setup again.

The Initial Setup appears on the screen each time the power is turned on

unless the Initial Set up is completed or "Never Show Again" is selected on the

first screen.

• To perform the Initial Setup again after the setting is completed, press ,

select "System Setup" - "Miscellaneous" - "Initial Setup", and press ENTER.

1. Speaker Setup

Select the connected speaker configuration.

Note that the image on the screen changes each time you select the number of

channels in "Speaker Channels".

2. Full Auto MCACC

Place the supplied speaker setup microphone at the listening position. The unit

automatically measures the test tones output from each speaker, and sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also reduces the effect of the standing

wave in accordance with the viewing environment and automatically adjusts the

equalizers for the speakers, and enables correction of sound distortion caused by

the acoustic environment of the room.

• It takes between 3 and 12 minutes for calibration to be completed. Each

speaker outputs the test tone at high volume during measurement, so be

careful of your surroundings. Also, keep the room as quiet as possible during

measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

•

If the power of this unit suddenly turns off, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

MCACC

SETUP MIC

When placing the speaker setup microphone on a tripod, refer to the

illustration.

2. Select "Next", and press ENTER. Then, test tones are output from each

speaker, and the connected speakers and the noise in the surrounding

environment are automatically measured.

3. The measurement results in step 2 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

• When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

•

When it cannot be resolved by performing the re-measurement, confirm

if the speakers are connected correctly. If there is any problem with the

speaker connection, perform the connection after disconnecting the power

cord.

4. Once the measurement is completed, it is possible to perform the

Summary of Contents for VSX-LX503















































































































































































Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands

Pioneer VSX-LX503, Instruction Manual

Search results

Summary of Contents for VSX-LX503

Reviews:

Related manuals for VSX-LX503

Brands by name

Popular brands