Pioneer VSX-1120-K, Operating Instructions Manual

Page: 63 / 108

Controlling the rest of your system 09
63
En
Programming signals from other
remote controls
If the pr eset code fo r you r com p onent is not available, o r
the available pr eset codes do not o p e r ate co rr ectly, you
can pr og r am signals f r om the r emote cont r ol of anothe r
com p onent. This can also be used to pr og r am additional
o p e r ations (buttons not cove r ed in the pr esets) afte r
assigning a pr eset code.
1
Ce r tain buttons r e pr esent o p e r ations that cannot be
lea r ned f r om othe r r emote cont r ols. The buttons
available a r e shown below:
1 Press and hold R.SETUP, then press “2” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess R.SETUP .
2 Press the input function button for the component
you want to control.
The LED blinks once and flashes continuously.
3 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this receiver’s remote control.
The LED blinks once and flashes continuously.
• The r emote cont r ols should be 3 cm (1 inch) a p a r t.
4 Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver’s remote control.
If the LED lights fo r one second, the setting has been
successfully com p leted.
2
5 To program additional signals for the current
component repeat steps 3 and 4.
To pr og r am signals fo r anothe r com p onent, exit and
r e p eat ste p s 2 th r ough 4.
6 Press R.SETUP to exit the programming mode.
Erasing one of the remote control
button settings
This e r ases one of the buttons you have pr og r ammed and
r esto r es the button to the facto r y default.
1 Press and hold R.SETUP, then press “7” for three
seconds.
The LED flashes continuously.
• To cancel the pr eset setu p mode pr ess
R.SETUP
.
2 Press the input function button corresponding to
the command to be erased, then press ENTER.
The LED flashes once.
3 Press and hold the button to be erased for three
seconds.
If the LED lights fo r one second, the e r asing has been
successfully com p leted.
4 Repeat step 3 to erase other buttons.
5 Press R.SETUP to exit the erasing mode.
Note
1 The r emote can sto r e about 120 pr eset codes f r om othe r com p onents (this has been tested with codes of Pionee r fo r mat only).
ZONE 2 ZONE 3 LIGHT
AUTO / ALC /
DIRECT
D.ACCESS
CH LEVEL A.ATT DIMMER
SIGNAL SEL MCACC SLEEP
HDMI OUT
TV / DTV MPX PQLS
PHASE CTRL STATUS THX
PGM
STEREO
iPod CTRL
HOME
MENU
TUNE
TUNE TOOLS LIST
PRESET
TOP MENU
BAND GUIDE
T.EDIT
VIDEO
PARAMETER
AUDIO
PARAMETER
ENTER PRESET
RETURN CATEGORY
MEMORY
STANDARD
MENU
ADV SURR
AUDIO
INFO
CLASS
ENTER
DISP
HDD DVD
5 4 6
8
0
7 9
2 1 3
/ CLR
CH
CH
TV CONTROL
INPUT
INPUT SELECT TV CTRL
iPod USB TUNER SIRIUS XM
ADAPTER NET RADIO CD TV
BD DVD
R.SETUP
SOURCE RECEIVER MULTI
OPERATION
DVR/BDR HDMI
RECEIVER
MUTE
MASTER
VOLUME
VOL
2 • Note that inte r fe r ence f r om TVs o r othe r devices will sometimes r esult in the r emote cont r ol lea r ning the w r ong signal.
• Some commands f r om othe r r emote cont r ols cannot be lea r ned, but in most cases the r emotes just need to be moved close r togethe r o r
fa r the r a p a r t.
• If the LED flashes fo r five seconds, it means the memo r y is full. See
Erasing all learnt settings that are in one input function
on p age 64 to
e r ase a pr og r ammed button you’ r e not using to f r ee u p mo r e memo r y (note that some signals may take mo r e memo r y than othe r s).
3 cm
(1 inch)
This r eceive r ’s
r emote cont r ol
Othe r r emote
cont r ol
VSX-1120_UXJCB.book 63 ページ ２０１０年３月１０日 水曜日 午後２時２分