Pioneer VSX-1120-K, Operating Instructions Manual

Page: 36 / 108

Basic Setup 04
36
En
If you have a t r i p od, use it to p lace the mic r o p hone so that
it’s about ea r level at you r no r mal listening p osition. If you
do not have a t r i p od, use some othe r object to install the
mic r o p hone.
1
The Full Auto MCACC dis p lay a pp ea r s once the
mic r o p hone is connected.
2
3 Select the parameters you want to set.
3
If the s p eake r s a r e connected using any setu p othe r than
Normal(SB/FH) , be su r e to set Speaker System befo r e
the Auto MCACC Setu p . See Speaker system setting on
p age 79.
• Speaker System
4
– Shows the cu rr ent settings.
When this is selected and ENTER is pr essed, the
s p eake r system selection sc r een a pp ea r s. Select the
pr o p e r s p eake r system, then pr ess RETURN to r etu r n.
• EQ Type – This dete r mines how the f r equency
balance is adjusted.
•
MCACC
– The six MCACC pr esets a r e used fo r sto r ing
su rr ound sound settings fo r diffe r ent listening
p ositions. Sim p ly choose an unused pr eset fo r now
(you can r ename it late r in
Data Management
on
p age 76).
• THX Speaker – Select YES if you a r e using THX
s p eake r s (set all s p eake r s to SMALL ), othe r wise leave
it set to NO .
4 Press and then select START.
5 Follow the instructions on-screen.
Make su r e the mic r o p hone is connected, and if you’ r e
using a subwoofe r , make su r e it is switched on and set to
a comfo r table volume level.
6 Wait for the test tones to finish, then confirm the
speaker configuration in the GUI screen.
A pr og r ess r e p o r t is dis p layed on-sc r een while the
r eceive r out p uts test tones to dete r mine the s p eake r s
pr esent in you r setu p . T r y to be as quiet as p ossible while
it’s doing this.
If no o p e r ations a r e p e r fo r med fo r 10 seconds while the
s p eake r configu r ation check sc r een is being dis p layed,
the Auto MCACC Setu p will r esume automatically. In this
case, you don’t need to select ‘ OK ’ and pr ess ENTER in
ste p 7.
• With e rr o r messages (such as Too much ambient
noise! o r Check microphone. ), select RETRY afte r
checking fo r ambient noise (see
Problems when
using the Auto MCACC Setup
on p age 37) and
ve r ifying the mic connection. If the r e doesn’t seem to
be a pr oblem, you can sim p ly select GO NEXT and
continue.
The configu r ation shown on-sc r een should r eflect the
actual s p eake r s you have.
• If you see an
ERR
message (o r the s p eake r
configu r ation dis p layed isn’t co rr ect), the r e may be a
pr oblem with the s p eake r connection.
If selecting
RETRY
doesn’t wo r k, tu r n off the p owe r
and check the s p eake r connections. If the r e doesn’t
seem to be a pr oblem, you can sim p ly use
/
to
select the s p eake r and
/
to change the setting
and continue.
Note
1 Install the mic r o p hone on a stable floo r . Placing the mic r o p hone on any of the following su r faces may make accu r ate measu r ement
im p ossible:
• Sofas o r othe r soft su r faces.
• High p laces such as tableto p s and sofa to p s.
2 If you leave the GUI sc r een fo r ove r five minutes, the sc r een save r will a pp ea r .
3 • When data measu r ement is taken, the r eve r b cha r acte r istics data (both befo r e- and afte r -calib r ation) that this r eceive r had been sto r ing will
be ove r w r itten. If you want to save the r eve r b cha r acte r istics data befo r e measu r ing, connect a USB memo r y device to this r eceive r and
t r ansfe r the data.
• When measu r ement is taken of the r eve r b cha r acte r istics data othe r than
SYMMETRY
, the data a r e not measu r ed afte r the co rr ection. If
you will need to measu r e afte r co rr ecting data, take the measu r ement using the EQ P r ofessional menu in the Manual MCACC setu p ( p age 71).
4 If you a r e p lanning on bi-am p ing you r f r ont s p eake r s, o r setting u p a se p a r ate s p eake r system in anothe r r oom, r ead th r ough
Speaker system
setting
on p age 79 and make su r e to connect you r s p eake r s as necessa r y befo r e continuing to ste p 4.
Speaker System : Normal(SB/FH)
1a.Full Auto MCACC
A/V RECEIVER
Exit Return
START
EQ Type : SYMMETRY
MCACC : M1.MEMORY 1
THX Speaker : NO
RECEIVER
Now Analyzing... 2/9
Environment Check
1a.Full Auto MCACC
A/V RECEIVER
Exit Cancel
Ambient Noise : OK
Microphone :
Speaker YES/NO
:
L : YES
FHL :
YES
C : YES
FHR :
YES
R : YES
SR :
YES
SBR : YES
SBL : YES
SL : YES
SW :
YES
1a.Full Auto MCACC
10
OK RETRY
A/V RECEIVER
Exit Cancel
VSX-1120_UXJCB.book 36 ページ ２０１０年３月１０日 水曜日 午後２時２分