Additional information
12
68
En
Settings
Display
Symptom
Cause
Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level in the room is too
high, or obstacles are blocking the setup
microphone.
• Keep the noise level in the room as low as possible
when using the Auto MCACC Setup (see
Other problems
when using the Auto MCACC Setup
on page 13 for more
on this). If the noise cannot be kept low enough, you will
have to set up the surround sound manually (page 43).
After using the Auto MCACC
Setup, the speaker size setting
(
LARGE
or
SMALL
) is incorrect.
• There was some inaudible low-frequency
noise in the room.
• The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto MCACC Setup.
Symptom
Cause
Remedy
The display is dark or off.
• The display is set to dark or off.
• Press
FL. DIMMER
on the remote control repeatedly to
select a different brightness.
After making an adjustment the
display goes off.
• The display is set to off.
• Press
FL. DIMMER
on the remote control repeatedly to
select a different brightness.
You can't get
DIGITAL
to display
when using the
SIGNAL SELECT
button.
• There is a problem with the digital
connections or the digital input is assigned
incorrectly.
• Check your digital connections and/or assign the digital
inputs correctly (see
Assigning the digital inputs
on
page 60).
• The multichannel analog inputs are
selected.
• Press
MULTI CH IN
again (see
Selecting the
multichannel analog inputs
on page 37).
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
• The player is paused.
• Press play.
• The player's sound output settings are
wrong.
• Set the player correctly (consult the manual that came
with the player, if necessary).
When playing a DVD-Audio disc,
the DVD player display shows
96
kHz
. However, the receiver’s
display does not.
• The audio from these discs is output from
the analog audio jacks of the DVD player only;
the receiver does not show the sampling rate
of the input signal through the analog inputs.
• This is not a malfunction. See also the operating
instructions that came with your DVD player.
During playback of a DTS 96/24
source, the display doesn't show
96kHz
.
• The receiver’s input signal type is set to
analog.
• Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
When playing Dolby Digital or
DTS sources, the receiver’s
format indicators do not light.
• No digital connection, or the digital
connection is incorrect.
• Check the digital audio connection (page 16).
• The receiver’s input signal type is set to
analog.
• Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
• The DVD player is set to output Dolby Digital
and/or DTS audio as PCM.
• Check the settings on the player. Set the output for
Dolby Digital and DTS (no PCM conversion). See also the
operating instructions that came with your DVD player.
• The disc has several playback audio tracks;
the one currently playing is actually PCM.
• Switch the playback audio channel on your DVD player.
See the operating instructions that came with your DVD
player.
When playing certain discs,
none of the receiver’s format
indicators light.
• The audio format of the disc is not 5.1/6.1
channel.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
When playing a disc, the
2
PL II
or
Neo:6
indicator lights
on the receiver.
• The input signal type is set to analog.
• Set the receiver to
AUTO
or
DIGITAL
(see
Choosing the
input signal
on page 33).
• A two channel soundtrack is currently
playing.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
• The soundtrack currently playing is
encoded using Dolby Surround.
• This is not a malfunction. Check the disc packaging for
details of the audio formats available on the disc.
During playback of a Surround
EX or DTS ES source on the
Extended AUTO
setting, the
EX
and
ES
indicators don’t light, or
the signal is not properly
processed.
•The source may be Dolby Surround EX / DTS
ES software, but it has no flag to indicate it is
6.1 compatible.
• Set to
Extended ON
(see
Using the surround back
channel (Extended mode)
on page 34) then switch to the
THX Surround EX or Standard EX listening mode (see
Listening in surround sound
on page 30).
VSX_1014.book.fm 68 ページ ２００４年５月１４日 金曜日 午前９時２４分
