Other connections
10
56
En
Chapter 10:
Other connections
Caution
•
Before making or changing the connections
, switch off
the power and disconnect the power cord from the
power outlet. Plugging in components should be the
last connection you make with your system.
• Be careful not to allow any contact between speaker
wires from different terminals.
• You can use speakers with a nominal impedance
between 6–16
Ω
(please see
Switching the speaker
impedance
on page 70 if you plan to use speakers
with an impedance of less than 8
Ω
).
Second Zone speaker B setup
After selecting
Second Zone
in
Surround back speaker
setting
on page 38, you can use the speakers connected
to the (surround back) B speaker terminals on the rear
panel to listen to stereo playback in another room. See
Switching the speaker system
below for the listening
options with this setup.
1
Connect a pair of speakers to the surround back
speaker terminals on the rear panel.
Connect them the same way you connected your
speakers in
Connecting the speakers
on page 20. Make
sure to review
Hints on speaker placement
on page 21
when placing the speakers in another room.
2
Select ‘Second Zone’ from the ‘Surr Back System’
menu.
See
Surround back speaker setting
on page 38 to do this.
Switching the speaker system
If you selected
Second Zone
in
Surround back speaker
setting
on page 38, three speaker system settings are
possible using the
SPEAKERS
button. If you selected
Normal (SB)
or
Front Bi-Amp
, the button will simply
switch your main speaker system on or off. The options
below are for the
Second Zone
setting only.
•
Use the SPEAKERS button on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
Normal (SB)
,
the button will simply switch your main speaker system
(A) on or off.
Press repeatedly to choose a speaker system option:
•
SP
A
– Sound is output from speaker system A and
the same signal is output from the pre-out terminals.
•
SP
B
– Sound is output from the two speakers
connected to speaker system B. Multichannel
sources will not be heard. The same signal is output
from the surround back channel pre-out terminals.
•
SP
AB
– Sound is output from speaker system A (up
to 5 channels, depending on the source), the two
speakers in speaker system B, and the subwoofer.
The sound from speaker system B will be the same as
the sound from speaker system A (multichannel
sources will be downmixed to 2 channels).
•
SP
(off) – No sound is output from the speakers. The
same sound is output from the pre-out terminals
(including from your subwoofer, if connected) as
when selecting speaker system A (above).
Note
• The subwoofer output depends on the settings you
made in
Manual speaker setup
on page 43. However,
if
SP
B
is selected above, no sound is heard from the
subwoofer (the LFE channel is not downmixed).
• Depending on the settings in
Surround back speaker
setting
on page 38 output from the surround back
pre-out terminals may change.
• All speaker systems (except
Second Zone
connections) are switched off when headphones are
connected.
PHONES
TUNER
CONTROL
TUNER
EDIT
SYSTEM
SETUP
RETURN
INPUT
ATT
FL
DIMMER
MCACC
SETUP MIC
DIGITAL IN
S-VIDEO
VIDEO
VIDEO2 INPUT
AUDIO
L
R
MULTI JOG
TUNING/
STATION
BAND
MPX
TONE
ACOUSTIC
EQ
DIALOG
ENHANCEMENT
MULTI CH
IN
SIGNAL
SELECT
EXTENDED
MODE
SPEAKERS
MIDNIGHT/
LOUDNESS
MULTI
JOG
MULTI
JOG
VSX_1014.book.fm 56 ページ ２００４年５月１４日 金曜日 午前９時２４分
