Pioneer Elite VSX-56TXi Operating Instructions Manual Download Page 98

Page: 98 / 104

Additional information

USB interface

Note

• If the unit does not operate normally due to external

effects such as static electricity, disconnect the
power plug from the outlet and insert again to return
to normal operating conditions.

Symptom

Cause

Remedy

No sound.

• The computer settings are incorrect.

• Make sure you have set up your computer system to
output through the USB interface (see

Using the USB

interface

on page 74).

• The software or source material you are
using is not compatible with USB output.

• Update to a more recent version of your existing
software, try a different audio program, or try a different
source.

• The volume control on your computer is set
too low.

• Turn up the volume on your computer.

VSX-56TXi_namiki.book 98 ページ２００４年５月６日　木曜日　午後５時３６分

Summary of Contents for Elite VSX-56TXi








































































































Search results

Summary of Contents for Elite VSX-56TXi

Reviews:

Related manuals for Elite VSX-56TXi

Brands by name

Popular brands

Pioneer Elite VSX-56TXi, Operating Instructions Manual

Search results

Summary of Contents for Elite VSX-56TXi

Reviews:

Related manuals for Elite VSX-56TXi

Brands by name

Popular brands