Pioneer DJM-900nexus, Operating Instructions Manual

Page: 22 / 184

DRB1569-A
En
22
22
Changing the settings
1 Press the [ON/OFF (UTILITY)] button for over 1 second.
The [ USER SETUP ] mode setting screen is displayed.
!
To display the [ CLUB SETUP ] mode setting screen, first turn this unit’s power off,
then press the [ POWER ] button while pressing the [ ON/OFF ( UTILITY )] button.
2 Press the [BEAT
c
,
d
] button.
Select the setting item.
3 Press the [TAP] button.
The screen switches to the setting item’s setting value change screen.
4 Press the [BEAT
c
,
d
] button.
Change the setting value.
5 Press the [TAP] button.
Enter the setting value.
The previous screen reappears.
! To return to the previous screen without changing the settings, press the
[ QUANTIZE ] button.
6 Press the [ON/OFF (UTILITY)] button.
Close the [
USER SETUP
] mode setting screen.
!
To close the [ CLUB SETUP ] mode setting screen, press the [ POWER ] button to
turn this unit’s power off.
About the auto standby function
When [ Auto Standby ] is set to [ ON ], the standby mode is set automatically if 4
hours pass with all of the conditions shown below met.
—
That none of this unit’s buttons or controls are operated.
— That no audio signals of
–10 dB
or greater are input to this unit’s input terminals.
—
That no PRO DJ LINK connections are made.
! When the [
LFO FORM
(
WAKE UP
)] button is pressed, the standby mode is
canceled.
! This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [ Auto Standby ] to [ OFF ].
About the talk over function
The talk over function has the two modes described below.
—
[ ADV ] (advanced talk over): The mid-range only of the sound of channels other
than the [
MIC
] channel is attenuated according to the [
Talk Over LEVEL
] setting
value and output.
dB
Frequency
—
[ NOR ] (normal talk over): The sound of channels other than the [ MIC ] channel is
attenuated according to the [
Talk Over LEVEL
] setting value and output.
dB
Frequency
Setting preferences
*: Setting upon purchase
Mode Options settings Screen display Setting value Descriptions
USER SETUP
Fader Start F.S. ON , OFF * Turns the fader start function on and off for all DJ players connected to the [ LINK ] terminals.
MIDI CH MIDI CH 1 * to 16 Sets the MIDI channel.
MIDI Button Type MIDI BT TGL *, TRG Selects the MIDI signal transmission mode, [ TGL ( TOGGLE )] or [ TRG ( TRIGGER )].
Talk Over Mode TLK MOD ADV *, NOR Selects the talk over function’s mode, [ ADV ( ADVANCED )] or [ NOR ( NORMAL )].
Talk Over LEVEL TLK LVL
–6 dB
,
-12 dB
,
-18 dB
*,
-24 dB
Sets the talk over function’s sound attenuation level.
CLUB SETUP
Digital Master Out
Level
DOUT LV
–19 dB * 、 –15 dB 、 –10
dB 、 –5 dB
Sets the maximum level of the sound output from the [ DIGITAL MASTER OUT ] terminals.
1
Digital Master Out
Sampling Rate
DOUT FS 48 kHz , 96 kHz * Sets the digital signal’s sampling rate.
MASTER ATT. MST ATT –6 dB , –3 dB , 0 dB *
Sets the attenuation level of the sound output from the [ MASTER1 ] and [ MASTER2 ] termi-
nals.
Auto Standby AUTOSTB ON *, OFF Turns the auto standby function on and off.
Mic Output To Booth
Monitor
MIC BTH ON *, OFF Sets whether or not to output the microphone’s audio signals from [ BOOTH ] terminals.
PC UTILITY PC UTLY ON *, OFF
Sets whether or not to launch the computer’s setting utility software automatically when a
USB cable is connected.
Factory Reset INITIAL YES , NO * Restores all the settings to their factory defaults.
1 : Note that the output sound may be distorted even if the master level indicator does not light up to the very top.